Pioneer VSX-1016TXV Owner's Manual - Page 52

11 Controlling the rest of your system • The remote controls should be 1 to 2 inches apart. 1 to 2 inches RECEIVER MULTI OPE THX STANDARD ADV. SURR SHIFT ISOPHASE MCACC S.DIRECT DVD CH STEREO REC STOP MEMORY STATUS SIGNAL SEL SBch CH AUDIO SUBTITLE HDD REC DTV INFO MUTE VOL BAND CLASS DISC ENTER CH LEVEL MENU ST T.EDIT RETURN ANALOG ATT RECEIVER TV CONT SYSTEM OFF SOURCE TV CH VIDEO SEL DIMMER INPUT SELECT CATEGORY TUNE GUIDE TV CONTROL XM RADIO TUNER VIDEO 2 VIDEO 1 ENTER DISP MPX TV VOL DTVMENU ST SETUP AV PARAMETER TOP MENU ì TUNE TV SAT CD-R i Pod D.ACCESS +10 SLEEP SR+ RECEIVER INPUT SELECT CD DVD DVR2 DVR1 5 Press the corresponding button on the other remote control that is sending (teaching) the signal to this receiver's remote control. For example, if you want to learn the playback control signal, press and hold briefly. The LCD display will show OK if the operation has been learned.1 If for some reasons the operation hasn't been learned the LCD will display ERROR briefly and then display PRES KEY again. If this happens, keep pressing the (teaching) button as you vary the distance between the two remotes, until the LCD display shows OK.2 Certain buttons represent operations that cannot be learned from other remote controls.3 The buttons available are shown below (with the exception of the TV controls, a combination of SHIFT and these buttons can also be learned): RECEIVER INPUT SELECT SYSTEM OFF SOURCE Erasing one of the remote control button settings This erases one of the buttons you have programmed and restores the button to the factory default. 1 While pressing the RECEIVER button, press SETUP. The remote LCD display shows SETUP. 2 Use / to select ERASE then press ENTER. The LCD on the remote prompts you for the component corresponding to the button setting to be erased. 3 Press the input source button corresponding to the command to be erased then press ENTER. The LCD display flashes PRES KEY. 4 Press and hold the button to be erased for two seconds. The LCD display shows OK or NO CODE to confirm the button has been erased. 5 Repeat step 4 to erase other buttons. 6 Press and hold the RECEIVER button for a couple of seconds when you're done. DVD CD TV CD-R DVR 2 DVR1 TV CTRL XM RADIO TUNER RECEIVER SLEEP SR+ DIALOG E SB ch DIMMER PHASE ANALOG ATT MIDNIGHT/ LOUDNESS S.RETRIEVER D.ACCESS +10 TOP MENU TUNE DTVMENU ST SETUP ENTER TUNE GUIDE CATEGORY CLASS DISC ENTER MENU ST T.EDIT RETURN BAND TV CONTROL TV VOL INPUT SELECT TV CH VOL DTV ON/OFF MPX REC DTV INFO MUTE REC STOP JUKEBOX AUDIO SUBTITLE HDD DVD DISP CH CH THX STANDARD ADV.SURR STEREO MULTI OPE AUTOSURR ACOUSTIC EQ SIGNAL SEL SHIFT EFFECT/CHSEL RECEIVER 6 To program additional signals for the current component repeat steps 4 and 5. To program signals for another component, exit and repeat steps 1 through 5. 7 Press and hold the RECEIVER button for a couple of seconds to exit and store the operation(s). Resetting the remote control presets This will erase all preset remote control preset codes and programmed buttons. 1 While pressing the RECEIVER button, press SETUP. The remote LCD display shows SETUP. 2 Use / to select RESET then press ENTER. RESET flashes in the LCD display. 3 Press and hold ENTER for about two seconds. The LCD shows OK to confirm the remote presets have been erased. Confirming preset codes Use this feature to check which preset code is assigned to an input source button. 1 While pressing the RECEIVER button, press SETUP. The remote LCD display shows SETUP. 2 Use / to select READ ID then press ENTER. The LCD on the remote prompts you for the input source button you want to check. Note 1 Note that interference from TVs or other devices will sometimes result in the remote control learning the wrong signal. 2 • Some commands from other remote controls cannot be learned, but in most cases the remotes just need to be moved closer together or farther apart. • If the remote LCD shows FULL, it means the memory is full. See Erasing one of the remote control button settings below to erase a programmed button you're not using to free up more memory (note that some signals may take more memory than others). 3 Note that the number key decimal button (+10/D.ACCESS) may not be learned with some components. 52 En