Pioneer VSX-815-S Owner's Manual - Page 72

Additional information, Resetting the main unit, Switching the speaker, impedance - factory reset

Get Pioneer VSX-815-S PDF manuals and user guides View all Pioneer VSX-815-S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 72 highlights

13 Additional information Resetting the main unit Use this procedure to reset all the receiver's settings to the factory default. Use the front panel controls to do this. 1 Switch the receiver into standby. 2 While holding down the TONE button, press and hold the STANDBY/ON button for about three seconds. 3 When you see RESET? appear in the display, press ENTER. OK? shows in the display. 4 Press SYSTEM SETUP to confirm. OK appears in the display to indicate that the receiver has been reset to the factory default settings. Switching the speaker impedance We recommend using speakers of 8Ω with this system, but it is possible to switch the impedance setting if you plan to use speakers with a 6Ω impedance rating. • With the receiver in standby, press STANDBY/ON while holding down the SPEAKERS button. Each time you do this, you switch between the impedance settings: • SP 6 OHM - Use this setting if your speakers are rated at 6Ω. • SP 8 OHM - Use this setting if your speakers are rated at 8Ω or more. 72 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
Additional information
13
72
En
Resetting the main unit
Use this procedure to reset all the receiver’s
settings to the factory default. Use the front
panel controls to do this.
1
Switch the receiver into standby.
2
While holding down the TONE button,
press and hold the
±
STANDBY/ON button for
about three seconds.
3
When you see RESET? appear in the
display, press
ENTER
.
OK?
shows in the display.
4
Press
SYSTEM SETUP
to confirm.
OK
appears in the display to indicate that the
receiver has been reset to the factory default
settings.
Switching the speaker
impedance
We recommend using speakers of 8
Ω
with this
system, but it is possible to switch the
impedance setting if you plan to use speakers
with a 6
Ω
impedance rating.
•
With the receiver in standby, press
±
STANDBY/ON
while holding down the
SPEAKERS
button.
Each time you do this, you switch between the
impedance settings:
•
SP 6 OHM
– Use this setting if your
speakers are rated at 6
Ω
.
•
SP 8 OHM
– Use this setting if your
speakers are rated at 8
Ω
or more.