Pioneer VSX-920-K Owner's Manual - Page 73

Problem, Remedy, secure to a wall or connect an outdoor FM antenna.

Get Pioneer VSX-920-K PDF manuals and user guides
UPC - 884938109369
View all Pioneer VSX-920-K manuals
Add to My Manuals
Save this manual to your list of manuals

Page 73 highlights

Additional information 11 English Deutsch Français Italiano Nederlands Español Problem Remedy No sound from subwoofer. • Make sure the subwoofer is switched on. • If the subwoofer has a volume knob, make sure it's turned up. • The Dolby Digital or DTS source you are listening to may not have an LFE channel. • Switch the subwoofer setting in Speaker Setting on page 45 to YES or PLUS. • Switch the LFE ATT (LFE Attenuate) on page 41 to LFEATT 0 or LFEATT 5. No sound from surround or • Connect the speakers properly (refer to page 19). center speakers. • Refer to Speaker Setting on page 45 to check the speaker settings. • Refer to Channel Level on page 47 to check the speaker levels. The PHASE CONTROL feature doesn't seem to have an audible effect. • If applicable, check that the lowpass filter switch on your subwoofer is off, or the lowpass cutoff is set to the highest frequency setting. If there is a PHASE setting on your subwoofer, set it to 0º (or depending on the subwoofer, the setting where you think it has the best overall effect on the sound). • Make sure the speaker distance setting is correct for all speakers (see Speaker Distance on page 48). Considerable noise in radio • Connect the antenna (page 29) and adjust the position for best broadcasts. reception. • Route any loose cables away from the antenna terminals and wires. • Fully extend the FM wire antenna, position for best reception, and secure to a wall (or connect an outdoor FM antenna). • Connect an additional internal or external AM antenna (page 29). • Turn off equipment causing interference or move it away from the receiver (or move antennas farther away from equipment causing noise). Broadcast stations cannot • Connect an outdoor antenna (refer to page 29). be selected automatically. Noise during playback of a • Move the cassette deck away from your receiver, until the noise cassette deck. disappears. Sound is produced from • Set the SIGNAL SEL to HDMI, C1/O1/O2 (DIGITAL) or A (analog) other components, but not according to the type of connections made (refer to page 43). from LD or DVD player. • Set the digital input settings correctly (refer to page 48). • Make digital connections (refer to page 24) and set the SIGNAL SEL to C1/O1/O2 (DIGITAL) (refer to page 43). • Refer to the instruction manual supplied with the DVD player. No sound is output or a • Set the digital volume level of the player to full, or to the neutral noise is output when position. software with DTS is played • Make sure the player's settings are correct and/or the DTS signal out is back. on. Refer to the instruction manual supplied with the DVD player. • Set the input signal type to C1/O1/O2 (DIGITAL) (see Choosing the input signal on page 43). 73 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
Additional information
11
73
En
English
Français
Deutsch
Nederlands
Italiano
Español
No sound from subwoofer.
• Make sure the subwoofer is switched on.
• If the subwoofer has a volume knob, make sure it’s turned up.
• The Dolby Digital or DTS source you are listening to may not have an
LFE channel.
• Switch the subwoofer setting in
S
p
eaker Setting
on page 45 to
YES
or
PLUS
.
•
Switch the
LFE ATT (LFE Attenuate)
on page 41 to
LFEATT 0
or
LFEATT 5
.
No sound from surround or
center speakers.
• Connect the speakers properly (refer to page 19).
• Refer to
S
p
eaker Setting
on page 45 to check the speaker settings.
• Refer to
Channel Level
on page 47 to check the speaker levels.
The
PHASE CONTROL
feature doesn’t seem to
have an audible effect.
• If applicable, check that the lowpass filter switch on your subwoofer is
off, or the lowpass cutoff is set to the highest frequency setting. If there is
a
PHASE
setting on your subwoofer, set it to 0º (or depending on the
subwoofer, the setting where you think it has the best overall effect on the
sound).
• Make sure the speaker distance setting is correct for all speakers (see
S
p
eaker Distance
on page 48).
Considerable noise in radio
broadcasts.
• Connect the antenna (page 29) and adjust the position for best
reception.
• Route any loose cables away from the antenna terminals and wires.
• Fully extend the FM wire antenna, position for best reception, and
secure to a wall (or connect an outdoor FM antenna).
• Connect an additional internal or external AM antenna (page 29).
• Turn off equipment causing interference or move it away from the
receiver (or move antennas farther away from equipment causing noise).
Broadcast stations cannot
be selected automatically.
• Connect an outdoor antenna (refer to page 29).
Noise during playback of a
cassette deck.
• Move the cassette deck away from your receiver, until the noise
disappears.
Sound is produced from
other components, but not
from LD or DVD player.
• Set the
SIGNAL SEL
to
HDMI
,
C1
/
O1
/
O2
(
DIGITAL
) or
A
(analog)
according to the type of connections made (refer to page 43).
• Set the digital input settings correctly (refer to page 48).
•
Make digital connections (refer to page 24) and set the
SIGNAL SEL
to
C1
/
O1
/
O2
(
DIGITAL
)
(refer to page 43).
• Refer to the instruction manual supplied with the DVD player.
No sound is output or a
noise is output when
software with DTS is played
back.
• Set the digital volume level of the player to full, or to the neutral
position.
• Make sure the player’s settings are correct and/or the DTS signal out is
on. Refer to the instruction manual supplied with the DVD player.
• Set the input signal type to
C1
/
O1
/
O2
(
DIGITAL
) (see
Choosing the
in
p
ut signal
on page 43).
Problem
Remedy