ProForm Endurance 720 E Instruction Manual - Page 7

Assembly

Get ProForm Endurance 720 E PDF manuals and user guides View all ProForm Endurance 720 E manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

ASSEMBLY • Assembly requires two persons. • Place all parts in a cleared area and remove the packing materials. Do not dispose of the packing materials until you finish all assembly steps. • Left parts are marked "L" or "Left" and right parts are marked "R" or "Right." • To identify small parts, see page 6. • In addition to the included tool(s), assembly requires the following tools: one Phillips screwdriver two adjustable wrenches one rubber mallet Assembly may be easier if you have your own set of wrenches. To avoid damaging parts, do not use power tools. 1. To register your product and activate your warranty in the UK, go to iconsupport.eu. If 1 you do not have internet access, call Customer Service (see the front cover of this manual).  To register your product and activate your warranty in Australia, email or post the following information to the email address or postal address on the front cover of this manual. • your receipt (make sure to keep a copy) • your name, address, and telephone number • the model number, serial number, and name of your product (see the front cover of this manual) 2. With the help of a second person, place some of the packing materials (not shown) under the rear 2 of the Frame (1). Have the second person hold the Frame to prevent it from tipping while you complete this step. Attach the Rear Stabilizer (2) to the Frame (1) with two M10 x 122mm Screws (104) and two M10 Split Washers (105). Then, remove the packing materials from under 21 the rear of the Frame (1). 104 105 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
7
• Assembly requires two persons.
• Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until you finish all assembly steps.
• Left parts are marked “L” or “Left” and right parts
are marked “R” or “Right.”
• To identify small parts, see page 6.
• In addition to the included tool(s), assembly
requires the following tools:
one Phillips screwdriver
two adjustable wrenches
one rubber mallet
Assembly may be easier if you have your own set
of wrenches. To avoid damaging parts, do not use
power tools.
ASSEMBLY
1
1.
To register your product and activate your
warranty in the UK,
go to iconsupport.eu. If
you do not have internet access, call Customer
Service (see the front cover of this manual).
To register your product and activate your
warranty in Australia,
email or post the
following information to the email address or
postal address on the front cover of this manual.
•
your receipt (make sure to keep a copy)
•
your name, address, and telephone number
•
the model number, serial number, and name
of your product (see the front cover of this
manual)
2.
With the help of a second person, place some of
the packing materials (not shown) under the rear
of the Frame (1).
Have the second person hold
the Frame to prevent it from tipping while you
complete this step.
Attach the Rear Stabilizer (2) to the Frame (1)
with two M10 x 122mm Screws (104) and two
M10 Split Washers (105).
Then, remove the packing materials from under
the rear of the Frame (1).
2
1
2
104
105