Ricoh Priport DX 4640PD Network Guide - Page 83

Commands List, TCP/IP address, Reference, Configuration

Get Ricoh Priport DX 4640PD PDF manuals and user guides View all Ricoh Priport DX 4640PD manuals
Add to My Manuals
Save this manual to your list of manuals

Page 83 highlights

Remote Maintenance by telnet Note ❒ If "Cannot write NVRAM information" appears, the changes are not saved. Repeat the steps above, as necessary. ❒ The network interface module is automatically reset when the changes are saved. ❒ When the network interface module is reset, active print jobs already sent to the printer will be finished. However, jobs not already sent will be canceled. Commands List Use the "help" command to display remote maintenance use. Note ❒ Enter "help" to display a list of commands that can be used. msh> help ❒ Enter "help command_name" to display information about the syntax of that command. msh> help command_name TCP/IP address Use the "ifconfig" command to configure the Ethernet interface, IEEE 802.11b interface, and the TCP/IP (IP address, subnet mask, broadcast address, default gateway address) for the printer. ❖ Reference msh> ifconfig 9 ❖ Configuration msh> ifconfig interface_name parameter address Interface name ether wlan *2 Interface to be configured Ethernet interface *1 IEEE 802.11b interface *1 If you did not enter an interface name, it will automatically be set to the Ethernet interface. *2 You can specify an interface when installing the IEEE 802.11b interface unit. Parameter Meaning (no parameter) IP address netmask subnet mask broadcast broadcast address 77

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
Remote Maintenance by telnet
77
9
Note
❒
If “Cannot write NVRAM information” appears, the changes are not
saved. Repeat the steps above, as necessary.
❒
The network interface module is automatically reset when the changes are
saved.
❒
When the network interface module is reset, active print jobs already sent
to the printer will be finished. However, jobs not already sent will be can-
celed.
Commands List
Use the “help” command to display remote maintenance use.
Note
❒
Enter “help” to display a list of commands that can be used.
msh> help
❒
Enter “help command_name” to display information about the syntax of that
command.
msh> help
command_name
TCP/IP address
Use the “ifconfig” command to configure the Ethernet interface, IEEE 802.11b in-
terface, and the TCP/IP (IP address, subnet mask, broadcast address, default
gateway address) for the printer.
❖
Reference
msh> ifconfig
❖
Configuration
msh> ifconfig
interface_name
parameter
address
*1
If you did not enter an interface name, it will automatically be set to the Ethernet
interface.
*2
You can specify an interface when installing the IEEE 802.11b interface unit.
Interface name
Interface to be configured
ether
Ethernet interface
*1
wlan
*2
IEEE 802.11b interface
Parameter
Meaning
(no parameter)
IP address
netmask
subnet mask
broadcast
broadcast address