Ricoh Priport DX 4640PD Network Guide - Page 95

spoolsw, msh> spoolsw, msh> spoolsw spool {on | off}

Get Ricoh Priport DX 4640PD PDF manuals and user guides View all Ricoh Priport DX 4640PD manuals
Add to My Manuals
Save this manual to your list of manuals

Page 95 highlights

Remote Maintenance by telnet Parameter key {key value} auth {open | shared} rate {auto | 11m | 5.5m | 2m | 1m} Value to be configured 64-bit or 128-bit can be set. Only 10 hexadecimal characters can be set when using 64-bit; or 26 hexadecimal characters when using 128-bit. Also, set 0x as the prefix. To use this function, set the same WEP key for all ports that transmit to each other. You can set the authorized mode when using WEP. The specified value and the authorized mode are as follows: open: Open system authorized (default) shared: Shared key authorized You can set the IEEE 802.11b transmission speed. The transmission speed you specify here is the speed at which data is sent. You can receive data at any speed. auto: automatically set (default) 11m: 11 Mbps fixed 5.5m: 5.5 Mbps fixed 2m: 2 Mbps fixed 1m: 1 Mbps fixed Note ❒ When changing the interface to IEEE 802.11b interface, see p.77 "TCP/IP address". ❒ When configuring the IEEE 802.11b interface TCP/IP, see p.77 "TCP/IP ad- dress". 9 spoolsw Use the "spoolsw" command to configure Job Spool settings. You can only specify diprint, lpr, ipp, ftp and smb protocol. • The "spoolsw" command for configuring Job Spool settings is available only when the optional hard disk is installed. ❖ View settings The Job Spool setting appears. msh> spoolsw ❖ Job Spool setting msh> spoolsw spool {on | off} Note ❒ Specify "on" to enable Job Spool, or "off" to disable it. 89

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
Remote Maintenance by telnet
89
9
Note
❒
When changing the interface to IEEE 802.11b interface, see p.77 “TCP/IP ad-
dress”.
❒
When configuring the IEEE 802.11b interface TCP/IP, see p.77 “TCP/IP ad-
dress”.
spoolsw
Use the “spoolsw” command to configure Job Spool settings.
You can only specify diprint, lpr, ipp, ftp and smb protocol.
•
The “spoolsw” command for configuring Job Spool settings is available only
when the optional hard disk is installed.
❖
View settings
The Job Spool setting appears.
msh> spoolsw
❖
Job Spool setting
msh> spoolsw spool {on | off}
Note
❒
Specify "on" to enable Job Spool, or "off" to disable it.
key {
key value
}
64-bit or 128-bit can be set.
Only 10 hexadecimal characters can be set
when using 64-bit; or 26 hexadecimal charac-
ters when using 128-bit.
Also, set 0x as the prefix.
To use this function, set the same WEP key
for all ports that transmit to each other.
auth {open | shared}
You can set the authorized mode when using
WEP. The specified value and the authorized
mode are as follows:
open: Open system authorized (default)
shared: Shared key authorized
rate {auto | 11m | 5.5m | 2m | 1m}
You can set the IEEE 802.11b transmission
speed.
The transmission speed you specify here is
the speed at which data is sent. You can re-
ceive data at any speed.
auto: automatically set (default)
11m: 11 Mbps fixed
5.5m: 5.5 Mbps fixed
2m: 2 Mbps fixed
1m: 1 Mbps fixed
Parameter
Value to be configured