Sanyo PLC-HF15000L Owner's Manual - Page 15

Remote Control Battery Installation, Remote Control Receivers and Operating Range, Wired Remote

Get Sanyo PLC-HF15000L - 15000 Lumens PDF manuals and user guides View all Sanyo PLC-HF15000L manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

Part Names and Functions Remote Control Battery Installation 1 Open the battery compartment lid. Pull up the lid and remove it. 2 Install new batteries into the compartment. 3 Two AAA size batteries For correct polarity (+ and -), be sure battery terminals are in contact with pins in the compartment. Replace the compartment lid. To ensure safe operation, please observe the following precautions : ● Use two (2) AAA or LR03 type alkaline batteries. ● Always replace batteries in sets. ● Do not use a new battery with a used battery. ● Avoid contact with water or liquid. ● Do not expose the remote control to moisture or heat. ● Do not drop the remote control. ● If the battery has leaked on the remote control, carefully wipe the case clean and install new batteries. ● Risk of an explosion if battery is replaced by an incorrect type. ● Dispose of used batteries according to the instructions or your local disposal rule or guidelines. Remote Control Receivers and Operating Range Point the remote control toward the projector (to Infrared Remote Receivers). The operating distance and angle between the receivers and the remote control must be shorter than 16.4' (5 m) and less than 60 degrees. Infrared Remote Receivers are located on the front, rear, and top panels. You can activate only necessary receivers. (pp. 10, 63). 16.4' (5 m) ✔Note: • W hen hanging the projector from the ceiling, select the Infrared Remote Receiver which is located farther away from the fluorescent light (p.63). • When placing the projector in the horizontal position, as fluorescent light may negatively affect the remote control signals, it is recommended to select either "Back" or "Front" to prevent the receiver on top of the projector from picking up the signals from the remote control. (p.63) 16.4' (5 m) Wired Remote Control The remote control can be used as a wired remote control. Wired remote control helps you use the remote control outside of the operating range (16.4'/ 5 m). Connect the remote control and the projector with the remote control cable (sold separately). Connected with the remote control cable, the remote control does not emit wireless signal. 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
Remote Control Battery Installation
1
2
3
Open the battery
compartment lid.
Install new batteries into
the compartment.
Replace the
compartment lid.
Two AAA size batteries
For correct polarity (+ and –),
be sure battery terminals are
in contact with pins in the
compartment.
To ensure safe operation, please observe the following precautions :
l
Use two (2) AAA or LR03 type alkaline batteries.
l
Always replace batteries in sets.
l
Do not use a new battery with a used battery.
l
Avoid contact with water or liquid.
l
Do not expose the remote control to moisture or heat.
l
Do not drop the remote control.
l
If the battery has leaked on the remote control, carefully wipe the case clean and install new batteries.
l
Risk of an explosion if battery is replaced by an incorrect type.
l
Dispose of used batteries according to the instructions or your local disposal rule or guidelines.
Part Names and Functions
15
Pull up the lid
and remove it.
Point the remote control toward the projector (to Infrared
Remote Receivers). The operating distance and angle
between the receivers and the remote control must be
shorter than 16.4’ (5 m) and less than 60 degrees.
Infrared Remote Receivers are located on the front,
rear, and top panels. You can activate only necessary
receivers. (pp. 10, 63).
16.4’
(5 m)
Remote Control Receivers and Operating Range
The remote control can be used as a wired remote control. Wired remote control helps you use the remote control outside
of the operating range (16.4’/ 5 m). Connect the remote control and the projector with the remote control cable (sold
separately). Connected with the remote control cable, the remote control does not emit wireless signal.
Wired Remote Control
16.4’
(5 m)
✔
Note:
•
When hanging the projector from the ceiling, select the
Infrared Remote Receiver which is located farther away
from the fluorescent light (p.63).
•
When placing the projector in the horizontal position, as
fluorescent light may negatively affect the remote control
signals, it is recommended to select either “Back” or
“Front” to prevent the receiver on top of the projector from
picking up the signals from the remote control. (p.63)