Sanyo PLC-XR70N Owners Manual - Page 24

Basic Operation, Turning On / Off the Projector

Get Sanyo PLC-XR70N - 70inch Rear Projection TV PDF manuals and user guides View all Sanyo PLC-XR70N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

BASIC OPERATION TURNING ON / OFF THE PROJECTOR Turning on the Projector 1 Connect the peripheral equipment (Computer, VCR, and etc.) before turning on the projector. (Refer to "CONNECTING TO THE PROJECTOR" on Pages 10~15 for connecting those equipment. 2 Connect the projector's AC power cord into a wall outlet and turn the MAIN ON/OFF switch (located on the Front Control) to the ON position. The LAMP POWER indicator lights RED, and the READY indicator lights GREEN. 3 Press the power ON/OFF button on the Remote Control Unit or on the projector to ON. The LAMP POWER indicator dims, and the Cooling Fans start to operate. The Preparation Display appears on the screen and the count-down starts. The signal from the source appears after 30 seconds. 30 The Preparation Display disappears after 30 seconds. Turning off the Projector 1 Press the power ON/OFF button on the Remote Control Unit or on the Front Control, and the message "Power off?" appears on the screen. 2 Press again the power ON/OFF button to turn off the projector. The LAMP POWER indicator lights bright and the READY indicator turns off. The Cooling Fans operate for 1 minute after the projector is turned off. (During this "Cooling Down" period, this appliance cannot be turned on.) 3 When the cooling the projector has finished, the READY indicator turns to green again and you can turn the projector on. To power down completely, turn the MAIN ON/OFF switch to the OFF position. THIS PROJECTOR USES AN UHP LAMP. TO MAINTAIN THE LIFE OF THE LAMP, ONCE YOU TURN IT ON, WAIT AT LEAST 5 MINUTES BEFORE TURNING IT OFF. When the TEMPERATURE WARNING indicator flashes red, the projector is automatically turned off. Wait at least 5 minutes before turning the projector on again. If the TEMPERATURE WARNING indicator continues to flash, follow procedures below: 1. Press the power ON/OFF button to OFF. 2. Check the air filters for dust accumulation. 3. Remove dust with vacuum cleaner. (See "AIR FILTER CARE AND CLEANING" section on page 46.) 4. Press the LAMP POWER ON/OFF button to ON. If the TEMPERATURE WARNING indicator still continues to flash, call your authorized dealer or service station. Power off? The message disappears after 4 seconds. 24

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
24
BASIC OPERATION
Turning on the Projector
Connect the projector's AC power cord into a wall outlet and turn
the MAIN ON/OFF switch (located on the Front Control) to the ON
position.
The LAMP POWER indicator lights RED, and the
READY indicator lights GREEN.
Press the power ON/OFF button on the Remote Control Unit or on
the projector to ON.
The LAMP POWER indicator dims, and the
Cooling Fans start to operate.
The Preparation Display appears
on the screen and the count-down starts.
The signal from the
source appears after 30 seconds.
2
3
Turning off the Projector
Press the power ON/OFF button on the Remote Control Unit or on
the Front Control, and the message "Power off?" appears on the
screen.
Press again the power ON/OFF button to turn off the projector.
The LAMP POWER indicator lights bright and the READY
indicator turns off.
The Cooling Fans operate for 1 minute after
the projector is turned off.
(During this "Cooling Down" period, this
appliance cannot be turned on.)
1
2
THIS PROJECTOR USES AN UHP LAMP.
TO
MAINTAIN THE LIFE OF THE LAMP, ONCE YOU TURN
IT ON, WAIT AT LEAST 5 MINUTES BEFORE TURNING
IT OFF.
Power off?
The message disappears after 4 seconds.
TURNING ON / OFF THE PROJECTOR
When the TEMPERATURE WARNING indicator flashes red, the
projector is automatically turned off.
Wait at least 5 minutes before
turning the projector on again.
If the TEMPERATURE WARNING indicator continues to flash, follow
procedures below:
1. Press the power ON/OFF button to OFF.
2. Check the air filters for dust accumulation.
3. Remove dust with vacuum cleaner.
(See "AIR FILTER CARE AND
CLEANING" section on page 46.)
4. Press the LAMP POWER ON/OFF button to ON.
If the TEMPERATURE WARNING indicator still continues to flash, call
your authorized dealer or service station.
1
Connect the peripheral equipment (Computer, VCR, and etc.)
before turning on the projector.
(Refer to "CONNECTING TO
THE PROJECTOR" on Pages 10~15 for connecting those
equipment.
3
When the cooling the projector has finished, the READY indicator
turns to green again and you can turn the projector on.
To power
down completely, turn the MAIN ON/OFF switch to the OFF
position.
30
The Preparation Display disappears after 30 seconds.