Home » Seagate Manuals » Hard Drives » Seagate ST800FM0022 » Manual Viewer

Seagate ST800FM0022 Pulsar.2 SAS Product Manual - Page 34

GB models in 6Gb operation

View all Seagate ST800FM0022 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

To obtain operating power for typical random write operations, refer to the following I/O rate curve (see Figure 7). Locate the typical I/O rate for a drive in your system on the horizontal axis and read the corresponding +5 volt current, +12 volt current, and total watts on the vertical axis. To calculate BTUs per hour, multiply watts by 3.4123. Figure 7. 200GB (at 6Gb) DC current and power vs. input/output operations per second 100GB models in 6Gb operation Typical power dissipation under idle conditions in 6Gb operation is 3.59 watts 12.25 BTUs per hour). To obtain operating power for typical random write operations, refer to the following I/O rate curve (see Figure 8). Locate the typical I/O rate for a drive in your system on the horizontal axis and read the corresponding +5 volt current, +12 volt current, and total watts on the vertical axis. To calculate BTUs per hour, multiply watts by 3.4123. Figure 8. 100GB (at 6Gb) DC current and power vs. input/output operations per second 6.5 ENVIRONMENTAL LIMITS Temperature and humidity values experienced by the drive must be such that condensation does not occur on any drive part. Altitude and atmospheric pressure specifications are referenced to a standard day at 58.7°F (14.8°C). Maximum wet bulb temperature is 82°F (28°C). Note. To maintain optimal performance drives should be run at nominal case temperatures. PULSAR.2 SAS PRODUCT MANUAL, REV. C 28

Section	Page
Pulsar®.2 SAS	1
Seagate Technology Support Services	7
1.0 Scope	8
2.0 Applicable standards and reference documentation	9
2.1 Standards	9
2.1.1 Electromagnetic compatibility	9
2.1.2 Electromagnetic compliance	10
2.1.3 European Union Restriction of Hazardous Substances (RoHS)	10
2.1.4 China Restriction of Hazardous Substances (RoHS) Directive	11
2.2 Reference documents	11
3.0 General description	12
3.1 Standard features	12
3.2 Media description	13
3.3 Performance	13
3.4 Reliability	13
3.5 Formatted capacities	13
3.6 Programmable drive capacity	14
3.7 Factory-installed options	14
3.8 Thin Provisioning	14
3.8.1 Logical Block Provisioning	14
3.8.2 Thin Provisioning capabilities	14
3.8.3 UNMAP	15
3.8.4 FORMAT UNIT command	15
3.8.5 Protection Information (PI) and Security (SED)	15
4.0 Performance characteristics	16
4.1 Internal drive characteristics	16
4.2 Performance characteristics	16
4.2.1 Access time	16
4.2.2 FORMAT UNIT command execution time for 512-byte LBA’s (minutes)	16
4.2.3 Performance	17
4.3 Start/stop time	18
4.4 Cache control	18
4.4.1 Caching write data	18
5.0 Reliability specifications	19
5.1 Error rates	19
5.1.1 Unrecoverable Errors	19
5.1.2 Interface errors	19
5.2 Endurance Management	20
5.2.1 Wear Leveling	20
5.2.2 Garbage Collection	20
5.2.3 Write Amplification	20
5.2.4 UNMAP	20
5.2.5 Data Retention	20
5.2.6 Lifetime Endurance Management (Available on select models)	20
5.2.7 SSD Percentage Used Endurance Indicator	20
5.3 Reliability and service	21
5.3.1 Annualized Failure Rate (AFR) and Mean Time Between Failure (MTBF)	21
5.3.2 Preventive maintenance	21
5.3.3 Hot plugging the drive	21
5.3.4 S.M.A.R.T.	21
5.3.5 Thermal monitor	22
5.3.6 Drive Self Test (DST)	23
5.3.7 Product warranty	24
6.0 Physical/electrical specifications	25
6.1 Power specifications	25
6.1.1 Power consumption	25
6.2 AC power requirements	25
6.3 DC power requirements	26
6.3.1 Conducted noise immunity	30
6.3.2 Power sequencing	30
6.3.3 Current profiles	30
6.4 Power dissipation	33
6.5 Environmental limits	34
6.5.1 Temperature	35
6.5.2 Relative humidity	35
6.5.3 Effective altitude (sea level)	35
6.5.4 Shock and vibration	36
6.5.5 Air cleanliness	37
6.5.6 Corrosive environment	37
6.5.7 Electromagnetic susceptibility	37
6.6 Mechanical specifications	38
7.0 About FIPS	40
8.0 About self-encrypting drives	41
8.1 Data encryption	41
8.2 Controlled access	41
8.2.1 Admin SP	41
8.2.2 Locking SP	41
8.2.3 Default password	41
8.3 Random number generator (RNG)	41
8.4 Drive locking	41
8.5 Data bands	42
8.6 Cryptographic erase	42
8.7 Authenticated firmware download	42
8.8 Power requirements	42
8.9 Supported commands	42
8.10 Sanitize - Cryptographic Erase	42
8.11 RevertSP	42
8.12 Sanitize Feature Set on SED Drives	42
9.0 Defect and error management	43
9.1 Drive internal defects/errors	43
9.2 Drive error recovery procedures	44
9.3 SAS system errors	44
9.4 Background Media Scan	44
9.5 Auto-Reallocation	44
9.6 Protection Information (PI)	45
9.6.1 Levels of PI	45
9.6.2 Setting and determining the current Type Level	45
9.6.3 Identifying a Protection Information drive	45
10.0 Installation	46
10.1 Drive orientation	46
10.2 Cooling	46
10.3 Drive mounting	47
10.4 Grounding	47
11.0 Interface requirements	48
11.1 SAS features	48
11.1.1 Task management functions	48
11.1.2 Task management responses	48
11.2 Dual port support	48
11.3 SCSI commands supported	49
11.3.1 INQUIRY data	53
11.3.2 MODE SENSE data	54
11.4 Miscellaneous operating features and conditions	59
11.4.1 SAS physical interface	59
11.4.2 Physical characteristics	62
11.4.3 Connector requirements	62
11.4.4 Electrical description	62
11.4.5 Pin descriptions	62
11.4.6 SAS transmitters and receivers	63
11.4.7 Power	63
11.5 Signal characteristics	63
11.5.1 Ready LED Out	63
11.5.2 Differential signals	64
11.6 SAS-2 Specification compliance	64

Match case Limit results 1 per page

ULSAR

.2 SAS P

RODUCT

ANUAL

, R

. C

To obtain operating power for typical random write operations, refer to the following I/O rate curve (see Figure 7). Locate the typical I/O rate

for a drive in your system on the horizontal axis and read the corresponding +5 volt current, +12 volt current, and total watts on the vertical

axis. To calculate BTUs per hour, multiply watts by 3.4123.

Figure 7.

200GB (at 6Gb) DC current and power vs. input/output operations per second

100GB models in 6Gb operation

Typical power dissipation under idle conditions in 6Gb operation is 3.59 watts 12.25 BTUs

per hour).

To obtain operating power for typical random write operations, refer to the following I/O rate curve (see Figure 8). Locate the typical I/O rate

for a drive in your system on the horizontal axis and read the corresponding +5 volt current, +12 volt current, and total watts on the vertical

axis. To calculate BTUs per hour, multiply watts by 3.4123.

Figure 8.

100GB (at 6Gb) DC current and power vs. input/output operations per second

6.5

NVIRONMENTAL LIMITS

Temperature and humidity values experienced by the drive must be such that condensation does not occur on any drive part. Altitude and

atmospheric pressure specifications are referenced to a standard day at 58.7°F (14.8°C). Maximum wet bulb temperature is 82°F (28°C).

Note.

To maintain optimal performance drives should be run at nominal case temperatures.