Sharp ER-A320 Programmer Manual - Page 19
Job#2710], Job#2711], Job#2900], <caution>, Job#2910, 2911] - not working
UPC - 074927900194
View all Sharp ER-A320 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 19 highlights
[JOB#2710] TAX TABLE PROGRAMMING 2710 @/FOR AB @/FOR Declaration of TAX XXXXXX TAX rate XXXX Cycle @/FOR XXX @/FOR Initial TAX XXXXX @/FOR XXXXX Lower TAX limit Break point @/FOR CA/AT @/FOR 72 BREAKPOINTS CAN BE PROGRAMMED FOR EACH TAX-TABLE. (Case of interval between break point is 1 dollar or more and less than 100 dollar. 36 breakpoints is programmed for each table.) DEPRESSION OF THE SBTL KEY AT THE FOLLOWING POINTS MEANS A TAX TABLE DELETE OPERATION. A : INTERVAL BETWEEN BREAKPOINTS IS = 1 1 DOLLAR OR MORE AND LESS THAN 100 DOLLAR INTERVAL BETWEEN BREAKPOINTS IS = 0 BELOW 1 DOLLAR B : TABLE 1 PROGRAMMING =1 TABLE 2 PROGRAMMING =2 TABLE 3 PROGRAMMING =3 TABLE 4 PROGRAMMING =4 TAX rate Cycle Initial TAX Lower TAX limit Break point 0.0000 - 99.9999% 0 - 9999 0 - 999 0 - 99999 0 - 99999 MRS = NO TAX [JOB#2711] TAX RATE PROGRAMMING 2711 @/FOR A @/FOR Declaration of TAX 0 XXXXX CA/AT Lower tax limit for add tax. XXXXXX TAX rate @/FOR CA/AT When lower tax limit is 0. DEPRESSlON OF THE ST KEY AT FOLLOWING POINTS PERFORM A TAX TABLE DELETE OPERATION. A : Tax programming A Tax 1 1 Tax 2 2 Tax 3 3 Tax 4 4 xxxxxx : Rate = 0.0000 ~ 99.9999% LOWER TAX LIMITATION max. 999.99 (This is invalid in VAT system.) MRS=0 [JOB#2900] (This JOB must be performed at X2/Z2 mode position. ) AUTO KEY SETTING 2900 @/FOR AUTO AUTO2 Max.20 (Free key) Delete AUTO AUTO2 CA/AT (Auto key function) This machine has [AUTO] key which can be programmed by the following key-Sequence. When [AUTO] key is depressed, the machine works the same as the programmed key-Sequence programed. Mode switch :(X2/Z2) 2900 @/FOR AUTO 1 PLU 100 DEPT2 AUTO TL Mode switch :(REG) Key entry R/J Display Comment AUTO PL001 1 same as 1 entry 5 1.10 001 1.10 same as PLU entry 02 5 1.00 1 same as 1 entry 10 same as 0 entry 100 same as 0 entry 02 1.00 same as DEPT2 entry Mode switch :(X2/Z2) 2900 @/FOR AUTO2 100 TL AUTO2 TL Mode switch :(REQ) Key entry R/J Display Comment DEPT1 01 5 1.00 01 1.00 AUTO2 1 same as 1 entry 5 1.00 TL 10 same as 0 entry 5 1.00 CA 100 same as 0 entry 5 1.00 CG C 0.00 same as TL entry [JOB#2910, 2911] Training mode start (#2910), End (#2911) 2910/2911 @/FOR CA/AT All operation is same as REG-mode operation. In the training mode, the concective number is printed as same number in receipt / journal printer. In the training mode, the concective number is counted up.