Sharp OZ-707 Operation Manual - Page 122

Appendix D, Troubleshooting

Get Sharp OZ-707 - Scientific Rom Card PDF manuals and user guides
UPC - 074000012141
View all Sharp OZ-707 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 122 highlights

APPENDIX D TROUBLESHOOTING This appendix provides you with some hints on what to do when your Card does not do what you expect it to. You should try each of the following suggestions. one at a time. until you have corrected the problem. (Refer to the Organizer Operation Manual.) 1. If the display is too light or too dark, • adjust the contrast control. 2. If the power does not come on (nothing is displayed), • the batteries may be exhausted. Replace the Organizer operating batteries. • the Card lock switch might not be set to the LOCK position. Check that the lock is set to the LOCK position. 3. If the power does not turn off, • the Card is running a program using a command which takes a long time, such as BEEP or SAVE "CAS:". Press the 00 key to interrupt program execution and then the []ff] key. If the power is still not turned off, perform the following operation 4. 4. If the Card does not operate properly, • a peripheral device may have been connected or disconnected while the power was on, or there may have been an error during program execution, or the Organizer may have been subjected to strong electrical noise or shocks during use. Perform one of the following operations. (1) Reset (retaining the memory contents) Press the RESET switch with a ball-point pen or any other 0 0 appropriate device and then the [Qff] keys. If the Organizer still operates improperly after clearing the error condition with this operation, there may be an error in programs CD or data entered. Follow (2) below, pressing the key to clear the Card memory contents. (2) All Reset (clearing the Card memory contents) 0 0 Press the RESET switch while holding the key. Release the RESET switch before releasing the 00 key. 232 When the RESET switch is released, the display shown at right will appear. CD (1) Press the key. The display shown at right will appear. t1AIN DATA ALL CLEAR OK (,(/~D ? Sl:CARD DATA ALL CLEAR OK (Y/N)? Caution: Do not press the [IJ key. Pressing the CD key will clear all data In the Organizer. (2) Press the I T ] key. • To clear the Card memory. press the I T ] key. (3) Reset the clock. • The clock data will be cleared as a result of the steps above. 233

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
APPENDIX D
TROUBLESHOOTING
This appendix provides you with some hints
on
what to do when your
Card does not do what you expect it to.
You
should try each of the
following suggestions. one at a time. until you have corrected the
problem.
(Refer
to
the
Organizer
Operation
Manual.)
1.
If the display is too light or too dark,
• adjust the contrast control.
2.
If the power does not come
on
(nothing is displayed),
• the batteries may
be
exhausted. Replace the Organizer operating
batteries.
• the Card lock switch might not be set
to
the LOCK position.
Check that the lock
is
set to the LOCK position.
3.
If the power does not turn off,
• the Card is running a program using a command which takes a
long time, such
as
BEEP or SAVE "CAS:". Press the
00
key to
interrupt program execution and then the
[]ff]
key.
If the power is still not turned off, perform the following operation
4.
4.
If the Card does not operate properly,
•
a peripheral device may have been connected or disconnected
while the power was on, or there may have been
an
error during
program execution, or the Organizer may have been subjected to
strong electrical noise or shocks during use.
Perform one of the following operations.
(1)
Reset
(retaining the memory contents)
Press the RESET switch with a ball-point pen or any other
appropriate device and then the
[Qff]
00
keys. If the
Organizer still operates improperly after clearing the error
condition with this operation, there may be
an
error
in
programs
or data entered. Follow (2) below, pressing the
CD
key
to
clear the Card memory contents.
(2)
All
Reset
(clearing the Card memory contents)
Press the RESET switch while holding the
00
key.
Release the RESET switch before releasing the
00
key.
232
When the RESET switch is released, the display shown at right will
appear.
(1) Press the
CD
key.
The display shown at right will appear.
t1AIN
DATA
ALL
CLEAR
OK
(,(/~D
?
Sl:CARD
DATA
ALL
CLEAR
OK
(Y/N)?
Caution:
Do
not
press
the
[IJ
key.
Pressing
the
CD
key
will
clear
all
data
In
the
Organizer.
(2) Press the
IT]
key.
•
To
clear the Card memory. press the
IT]
key.
(3) Reset the clock.
• The clock data will
be
cleared as a result of the steps above.
233