Sharp PG-A10X Operation Manual - Page 63

Resetting the Lamp Timer - lamp reset

Get Sharp PG-A10X - Notevision XGA LCD Projector PDF manuals and user guides
UPC - 074000358843
View all Sharp PG-A10X manuals
Add to My Manuals
Save this manual to your list of manuals

Page 63 highlights

5 Remove the lamp unit. • Loosen the securing screws from the lamp unit. Hold the lamp unit by the handle and pull it in the direction of the arrow. At this time, keep the lamp unit horizontal and do not tilt it. 6 Insert the new lamp unit. • Press the lamp unit firmly into the lamp unit compartment. Fasten the securing screws. 7 Replace the filter/lamp unit cover. • Align the tab on the filter/lamp unit cover (1) and place it while pressing the tab (2) to close it. Then tighten the user service screw (3) to secure the filter/ lamp unit cover. Info • If the lamp unit and filter/lamp unit cover are not correctly installed, the power will not turn on, even if the power cord is connected to the projector. Securing screws 1 2 Handle 3 User service screw Resetting the Lamp Timer Reset the lamp timer after replacing the lamp. 1 Connect the power cord. • Plug the power cord into the AC socket of the projector. 2 Reset the lamp timer. • While simultaneously holding down and on the projector, press and on the projector. • "LAMP 0000H" is displayed, indicating that the lamp timer is reset. Info • Make sure to reset the lamp timer only when replacing the lamp. If you reset the lamp timer and continue to use the same lamp, this may cause the lamp to become damaged or explode. A10X_A10S#E_Print#p51_62.p65 59 AC socket Power ON button Volume buttons AUTO SYNC button 59 03.2.4, 2:07 PM Appendix

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
59
Appendix
5
Remove the lamp unit.
•
Loosen the securing screws from the
lamp unit. Hold the lamp unit by the
handle and pull it in the direction of the
arrow. At this time, keep the lamp unit
horizontal and do not tilt it.
6
Insert the new lamp unit.
•
Press the lamp unit firmly into the lamp
unit compartment. Fasten the securing
screws.
7
Replace the filter/lamp unit
cover.
•
Align the tab on the filter/lamp unit cover
(
1
) and place it while pressing the tab
(
2
) to close it. Then tighten the user
service screw (
3
) to secure the filter/
lamp unit cover.
Info
•
If the lamp unit and filter/lamp unit cover
are not correctly installed, the power will
not turn on, even if the power cord is con-
nected to the projector.
Resetting the Lamp Timer
Reset the lamp timer after replacing the lamp.
1
Connect the power cord.
•
Plug the power cord into the AC socket
of the projector.
2
Reset the lamp timer.
•
While simultaneously
holding down
and
on the projector, press
and
on the projector.
•
“
LAMP 0000H
”
is displayed, indicating
that the lamp timer is reset.
Info
•
Make sure to reset the lamp timer only
when replacing the lamp. If you reset the
lamp timer and continue to use the same
lamp, this may cause the lamp to become
damaged or explode.
Securing screws
Handle
1
3
2
User service screw
AC socket
Power ON button
Volume
buttons
AUTO SYNC
button
A10X_A10S#E_Print#p51_62.p65
03.2.4, 2:07 PM
59