Sharp R930AK Service Manual - Page 32
Control Panel Assembly And Control Unit Removal - rear view
UPC - 074000606036
View all Sharp R930AK manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 32 highlights
R-930AK R-930AW 8. Remove the magnetron air guide from the waveguide. 9. Disconnect wire leads from the fan motor. 10. Release the main harness from the hole of the fan duct. 11. Release the thermistor harness from the hole of the fan duct. 12. Release one (1) tab holding the fan duct to the rear cabinet. 13. Release one (1) tab holding the fan duct to the air guide (Right). 14.Remove the fan duct assembly from the oven. 15.Remove the fan blade from the fan motor shaft according the following procedure. 1) Hold the edge of the rotor of the fan motor by using a pair of grove joint pliers. CAUTION: * Make sure that any pieces do not enter the gap between the rotor and the stator of the fan motor because the rotor is easily shaven by pliers and metal pieces may be produced. * Do not touch the pliers to the coil of the fan motor because the coil may be cut or injured. * Do not disfigure the bracket by touching with the pliers. 2) Remove the fan blade from the shaft of the fan motor by pulling and rotating the fan blade with your hand. 3) Now, the fan blade will be free. CAUTION: * Do not use this removed fan blade again because the hole (for shaft) of it may become bigger than a standard one. 16.Remove the two (2) screws and nuts holding the fan motor to the fan duct. 17.Now, the fan motor is free. Coil INSTALLATION 1. Install the fan motor to the fan duct with the two (2) screws and nuts. 2. Install the fan blade to the fan motor shaft according the following procedure. 1) Hold the center of the bracket which supports the shaft of the fan motor on the flat table. 2) Apply the screw lock tight into the hole (for shaft) of the fan blade. 3) Install the fan blade to the shaft of fan motor by pushing the fan blade with a small, light weight, ball peen hammer or rubber mallet. CAUTION: * Do not hit the fan blade strongly when installed because the bracket may be disfigured. * Make sure that the fan blade rotates smooth after installation. * Make sure that the axis of the shaft is not slanted. 3. Reset the fan duct assembly to its place. 4. Install the tabs of fan duct to the rear cabinet and air guide. 5. Install the magnetron air guide with the one (1) screw. 6. Reinstall the main harness and thermistor harness to each hole of the fan duct. 7. Reinstall the chassis support to the control panel back plate, waveguide and rear cabinet with the three (3) screws. 8. Re-connect the wire leads to the fan motor, referring to the pictorial diagram. 9. Re-install the fan motor grounding wire to the air guide (Right) with one (1) screw. Shaft Groove joint pliers Rear View Stator Gap Bracket Rotor Side View Shaft Axis Stator Rotor Table These are the position where should be pinched with pliers Center of bracket CONTROL PANEL ASSEMBLY AND CONTROL UNIT REMOVAL To remove the control panel, procedure as follows: 1. Disconnect oven from power supply and remove outer case. 2. Discharge high voltage capacitor. 3. Disconnect connector CN-A, CN-E and CN-F from the control unit. 4. Disconnect the wire leads from the relays RY1, RY2 and RY3. 5. Remove one (1) screw holding the control panel back plate to the chassis support. 6. Remove two (2) screws holding the bottom edge of the back plate to the cabinet base. 7. Remove one (1) screw holding the back plate to the oven cavity flange. 8. Lift up and pull the control panel assembly forward. Replacement of individual component is as follows; CONTROL UNIT AND KEY UNIT 1. Disconnect the wire connector from the control unit. 2. Remove the four (4) screws holding the panel frame to the back plate. 3. Separate the panel frame and back plate. 4. Remove the three (3) screws holding the control unit to the panel frame. 5. Lift up the control unit and disconnect the key connector from the control unit. 6. Now, the control unit and frame assembly are separated. NOTE; 1. Before attaching a new key unit, remove remaining adhesive on the control panel frame surfaces completely with alcohol and so on. 2. When a attaching the key unit to the control panel frame, adjust the lower edge and right edge of the key unit to the correct position of the control panel frame. 3. Stick the key unit firmly to the control panel frame by rubbing with soft cloth not to scratch. 30