Snapper 150Z Operater's Manual - Page 30

Service & Adjustments, Ground Speed Control Lever, Adjustment, Speed Balancing Adjustment,

Get Snapper 150Z PDF manuals and user guides View all Snapper 150Z manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

Maintenance Service & Adjustments Ground Speed Control Lever C Adjustment The control levers have three adjustments: To Adjust Control Lever Height: Pull the levers in A across the operator's lap to their DRIVE positions. Loosen the mount bolts (D, Figure 30) and raise or lower the levers to the desired position. Tighten the mounting D bolts.(D). To Adjust Control Lever End Gap: The control lever B end gap (C, Figure 31) should be adjusted so that the levers do not contact each other when placed in DRIVE positions. Loosen the jam nut (A, Figure 30) and adjust E the length of the carriage bolt (B) so that the levers do not contact each other. Repeat on the opposite side. Tighten the jam nut (A) to lock the carriage bolt in position. Figure 30. Control Lever Adjustment To Adjust Operator Clearance: The space between the operator and the control levers can be increase by r n removing the lower mounting bolt (D, Figure 30), pivoting the lever forward, and reinstalling the capscrew through fo tio the control lever and forward slot (C). Repeat with the other ground speed lever. ot uc Speed Balancing Adjustment N d If the rider veers to the right or left when the ground speed control levers are in the maximum forward o position, the top speed of the right lever can be balanced r by turning the adjustment knob (E, Figure 30). Loosen the jam nut and turn the knob COUNTERCLOCKWISE p to increase speed or CLOCKWISE to decrease speed. Re Tighten the jam nut when complete. C A B MORWAIESRE HCeuitgthintg MLOO1W7W342E7E6RR 4 High Cut 3 2 1 1733458 Low Cut Cutting Height Adjustment To increase the mower cutting height (raise the mower deck), press the top of the mower cutting height switch (A, Figure 31) To decrease mower cutting height (lower the mower deck), press the bottom of the switch. Mower cutting height range is 3-3/4" to 1-1/2". The cutting height gauge indicates the position of the mower deck.. The cutting height gauge (B) is located on the front of the rider, just behind the driver's left leg. Figure 31. Cutting Height Adjustment PTO Clutch Adjustment See CHECK / ADJUST PTO CLUTCH. 30

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
30
Service & Adjustments
Ground Speed Control Lever
Adjustment
The control levers have three adjustments:
To Adjust Control Lever Height:
Pull the levers in
across the operator’s lap to their DRIVE positions.
Loosen the mount bolts (D, Figure 30) and raise or lower
the levers to the desired position.
Tighten the mounting
bolts.(D).
To Adjust Control Lever End Gap:
The control lever
end gap (C, Figure 31) should be adjusted so that the
levers do not contact each other when placed in DRIVE
positions.
Loosen the jam nut (A, Figure 30) and adjust
the length of the carriage bolt (B) so that the levers
do not contact each other.
Repeat on the opposite
side.
Tighten the jam nut (A) to lock the carriage bolt in
position.
To Adjust Operator Clearance:
The space between
the operator and the control levers can be increase by
removing the lower mounting bolt (D, Figure 30), pivoting
the lever forward, and reinstalling the capscrew through
the control lever and forward slot (C).
Repeat with the
other ground speed lever.
Speed Balancing Adjustment
If the rider veers to the right or left when the ground
speed control levers are in the maximum forward
position, the top speed of the right lever can be balanced
by turning the adjustment knob (E, Figure 30).
Loosen
the jam nut and turn the knob COUNTERCLOCKWISE
to increase speed or CLOCKWISE to decrease speed.
Tighten the jam nut when complete.
Cutting Height Adjustment
To increase the mower cutting height (raise the mower
deck), press the top of the mower cutting height switch
(A, Figure 31)
To decrease mower cutting height (lower
the mower deck), press the bottom of the switch.
Mower
cutting height range is 3-3/4” to 1-1/2”.
The cutting
height gauge indicates the position of the mower deck..
The cutting height gauge (B) is located on the front of the
rider, just behind the driver’s left leg.
PTO Clutch Adjustment
See CHECK / ADJUST PTO CLUTCH.
Figure 30.
Control Lever Adjustment
A
C
E
B
D
1
4
3
2
Figure 31.
Cutting Height Adjustment
A
C
B
Maintenance
Not for
Reproduction