Home » Sony Manuals » Home Theater Systems » Sony BDV-HZ970W » Manual Viewer

Sony BDV-HZ970W Operating Instructions - Page 53

Setting the Speakers, Speaker Settings] - install

UPC - 027242780712

Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

Other Operations AECM.MCI-CAACL2 Calibration mic 6 Press X/x to select [OK]. To cancel, select [Cancel]. 7 Press . [Auto Calibration] starts. The system adjusts the speaker settings automatically. For proper calibration results, please remain quiet during the measurement. Note • Before [Auto Calibration], make sure that the surround amplifier turns on and you install the surround amplifier in the appropriate location. If you install the surround amplifier in an improper location, such as another room, proper measurement will not be obtained. • When you use the Wireless Surround Speaker Kit (WAHT-SBP2, optional) for the surround back speakers (page 17), install the speakers in appropriate location and turn the surround amplifier on. To use the surround back speakers, set [Surround Back] in [Speaker Settings] to [Yes] (page 54) 8 Confirm the result of [Auto Calibration]. The conclusions appear on the TV screen. Press C/c to change the page. The first page shows the distance of the speakers. The second page shows the level of the speakers. Note • If measurement fails, follow the message then retry [Auto Calibration]. 9 Press X/x to select [OK] or [Cancel], then press . x The measurement is OK. Disconnect the calibration mic, then select [OK]. The result is implemented. x The measurement is not OK. Follow the message, then select [OK] to retry. Note • While the Auto Calibration function works: - do not turn off the power. - do not press any button. - do not change the volume. - do not change the function. - do not change the disc. - do not insert a disc. - do not disconnect the calibration mic. Setting the Speakers [Speaker Settings] To obtain the best possible surround sound, set connection of the speakers and their distance from your listening position. Then use the test tone to adjust the level and the balance of the speakers to the same level. 1 Press HOME. The home menu appears on the TV screen. 2 Press C/c to select [Setup]. 3 Press X/x to select [Audio Settings], then press . 4 Press X/x to select [Speaker Settings], then press . The [Speaker Settings] display appears. 53US

Section	Page
WARNING	2
About These Operating Instructions	5
Unpacking	7
Preparing the remote	9
Index to Parts and Control	10
Front panel	10
Front panel display	11
Rear panel	12
Surround amplifier	13
Remote control	14
Getting Started	16
Step 1: Installing the System	16
Positioning the speakers	16
Assembling the speakers	18
When installing the speakers on a wall	18
Step 2: Connecting the System	21
Connecting the speakers	21
Connecting the TV (Video connection)	22
Connecting the TV (Audio connection)	23
Connecting the other components	24
Connecting the antenna (aerial)	26
Inserting the wireless transceiver	27
Step 3: Connecting to the Network	28
Wired Setup	28
USB Wireless Setup	28
Step 4: Setting up the S-AIR Wireless System	29
Step 5: Performing the Easy Setup	30
Step 6: Selecting the Source	32
Step 7: Enjoying Surround Sound	33
Selecting surround settings based on your listening preference	33
Playback	35
Playing a Disc	35
Enjoying BONUSVIEW/BD-LIVE	35
Enjoying Blu-ray 3D	35
Displaying the play information	36
Playing from a USB Device	36
Enjoying an iPod	37
Playing via a Network	38
Streaming BRAVIA Internet Video	38
Playing files stored on a DLNA server	38
Available Options	38
Adjusting the delay between the picture and sound	40
Sound Adjustment	41
Selecting the Effect to Suit the Source	41
Selecting the Audio Format, Multilingual Tracks, or Channel	41
Enjoying Multiplex Broadcast Sound	42
Using the Sound Effect	43
Enjoying sound at low volume	43
Changing the tonal balance	43
Tuner	44
Listening to the Radio	44
Presetting radio stations	44
Selecting the preset station	45
Selecting a radio station by inputting a frequency directly	45
External Audio Device	46
Using an S-AIR Product	46
Setting the S-AIR ID to activate wireless transmission	46
Enjoying the system’s sound in another room	47
Enjoying the S-AIR receiver while the unit is in standby mode	47
Identifying the unit with a specific S-AIR sub unit (Pairing operation)	48
Checking the S-AIR status of the unit	48
If wireless transmission is unstable	49
Other Operations	50
Using the Control for HDMI Function for “BRAVIA” Sync	50
Preparing for the Control for HDMI function	50
Turning the system off in sync with the TV	51
Watching BD/DVD by a single button press	51
Enjoying a component that is connected to the system via an HDMI cable	51
Using the Theater Mode	51
Enjoying the sound of the content on the TV screen via the system’s speakers	51
Setting the Maximum Volume Level of the System	52
Receiving the digital audio signal of the TV	52
Operating the system via the TV remote	52
Changing the language for the on-screen display of the TV	52
Calibrating the Appropriate Settings Automatically	52
Setting the Speakers	53
Using the Sleep Timer	55
Deactivating the Buttons on the Unit	55
Controlling Your TV or Other Components with the Supplied Remote	56
Controlling your components with the supplied remote	56
Changing the preset code of the remote (Preset mode)	57
Programming the remote code from another remote (Learning mode)	57
Clearing all the preset and programmed remote codes from the remote’s memory	58
Saving Power in Standby Mode	58
Settings and Adjustments	59
Using the Setup Display	59
[Remote Controller Setting Guide]	59
[Network Update]	60
[Screen Settings]	60
[Audio Settings]	61
[BD/DVD Viewing Settings]	62
[Parental Control Settings]	62
[Music Settings]	63
[System Settings]	63
[Network Settings]	64
[Easy Setup]	65
[Resetting]	65
Additional Information	66
Precautions	66
Notes about the Discs	67
Troubleshooting	68
Playable Discs	75
Playable Types of Files	76
Supported Audio Formats	77
Video Output Resolution	77
Specifications	78
Language Code List	81
Parental Control/Area Code List	81
Glossary	82

Match case Limit results 1 per page

Other Operations

Press

to select [OK].

To cancel, select [Cancel].

Press

[Auto Calibration] starts.

The system adjusts the speaker settings

automatically.

For proper calibration results, please

remain quiet during the measurement.

Note

• Before [Auto Calibration], make sure that the

surround amplifier turns on and you install the

surround amplifier in the appropriate location. If

you install the surround amplifier in an improper

location, such as another room, proper

measurement will not be obtained.

• When you use the Wireless Surround Speaker

Kit (WAHT-SBP2, optional) for the surround

back speakers (page 17), install the speakers in

appropriate location and turn the surround

amplifier on. To use the surround back speakers,

set [Surround Back] in [Speaker Settings] to

[Yes] (page 54)

Confirm the result of [Auto

Calibration].

The conclusions appear on the TV screen.

Press

to change the page. The first page

shows the distance of the speakers. The

second page shows the level of the

speakers.

Note

• If measurement fails, follow the message then

retry [Auto Calibration].

Press

to select [OK] or [Cancel],

then press

The measurement is OK.

Disconnect the calibration mic, then select

[OK]. The result is implemented.

The measurement is not OK.

Follow the message, then select [OK] to

retry.

Note

• While the Auto Calibration function works:

–

do not turn off the power.

–

do not press any button.

–

do not change the volume.

–

do not change the function.

–

do not change the disc.

–

do not insert a disc.

–

do not disconnect the calibration mic.

Setting the Speakers

[Speaker Settings]

To obtain the best possible surround sound, set

connection of the speakers and their distance

from your listening position. Then use the test

tone to adjust the level and the balance of the

speakers to the same level.

Press HOME.

The home menu appears on the TV screen.

Press

to select

[Setup].

Press

to select [Audio Settings],

then press

Press

to select [Speaker Settings],

then press

The [Speaker Settings] display appears.

A.CAL

MIC

ECM-AC2

Calibration mic