Sony DVP-CX850D Operating Instructions - Page 67

Controlling the TV or the AV Receiver (Amplifier) with the Supplied Remote - replacement remote

Get Sony DVP-CX850D - Cd/dvd Player PDF manuals and user guides View all Sony DVP-CX850D manuals
Add to My Manuals
Save this manual to your list of manuals

Page 67 highlights

Adjusting the speaker volume 1 While you stop playback, select "SPEAKER SETUP" after pressing SET UP. 2 Select "TEST TONE" and set "TEST TONE" to "ON." You will hear the test tone from each speaker in sequence. 3 From your listening position, select "BALANCE" or "LEVEL" and adjust the value of "BALANCE" and "LEVEL" using >/.. During this adjustment, the test tone is emitted from both speakers simultaneously. 4 Select "TEST TONE" and set "TEST TONE" to "OFF" to turn off the test tone. Controlling the TV or the AV Receiver (Amplifier) with the Supplied Remote Z If you adjust the remote signal, you can control your TV with the supplied remote. Default setting is to control Sony TVs with the g mark. When you connect the player to a Sony AV receiver (amplifier), you can also set the input of the receiver (amplifier) to this player with the supplied remote. TV/DISC EXPLORER/ DVD switch Number buttons 123 45 6 789 0 A B C D ALL DVD CD 1/u (POWER) Settings and Adjustments Controlling TVs with the remote 1 Slide the TV/DISC EXPLORER/DVD switch to TV. 2 Hold down 1/u (POWER), and enter your TV's manufacturer's code (see the table on the next page) using the number buttons. Then release 1/u (POWER). Code numbers of controllable TVs If more than one code number is listed, try entering them one at a time until you find the one that works with your TV. Notes • If you enter a new code number, the code number previously entered will be erased. • When you replace the batteries of the remote commander, the code number may reset to 01 (Sony). Reset the appropriate code number. 67

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
67
Settings and Adjustments
Adjusting the speaker volume
1
While you stop playback, select “SPEAKER SETUP”
after pressing SET UP.
2
Select “TEST TONE” and set “TEST TONE” to “ON.”
You will hear the test tone from each speaker in
sequence.
3
From your listening position, select “BALANCE” or
“LEVEL” and adjust the value of “BALANCE” and
“LEVEL” using
>
/
.
.
During this adjustment, the test tone is emitted from
both speakers simultaneously.
4
Select “TEST TONE” and set “TEST TONE” to “OFF”
to turn off the test tone.
Controlling the TV or the
AV Receiver (Amplifier)
with the Supplied Remote
Z
If you adjust the remote signal, you can control your TV
with the supplied remote.
Default setting is to control
Sony TVs with the
g
mark.
When you connect the player to a Sony AV receiver
(amplifier), you can also set the input of the receiver
(amplifier) to this player with the supplied remote.
Controlling TVs with the remote
1
Slide the TV/DISC EXPLORER/DVD switch to TV.
2
Hold down
1
/
u
(POWER), and enter your TV’s
manufacturer’s code (see the table on the next
page) using the number buttons.
Then release
1
/
u
(POWER).
Code numbers of controllable TVs
If more than one code number is listed, try entering them
one at a time until you find the one that works with your
TV.
Notes
• If you enter a new code number, the code number previously
entered will be erased.
• When you replace the batteries of the remote commander, the
code number may reset to 01 (Sony). Reset the appropriate code
number.
Number buttons
TV/DISC EXPLORER/
DVD switch
1
/
u
(POWER)
1
2
3
4
5
6
7
8
9
0
A
B
C
D
ALL
DVD
CD