Sony RM-VL1000 Operating Instructions - Page 28

28

Notes on learning the

signals of an air-

conditioner

About seasonal adjustments

If you change the settings of the

air-conditioner for the season, you

have to program the remote

control signals of the new settings

on the Commander.

If the power-on/off operation

does not work correctly

The air-conditioner may not be

turned on or off properly with the

button or key of this Commander,

for which you have programmed

its power-on/off signal.

If the Commander can operate

only

“

ON

”

with one button or

label and

“

OFF

”

with another,

while your air-conditioner

’

s

remote control can operate

“

ON/

OFF

”

with a single button or label,

program the signal on two buttons

or labels of the Commander as

follows.

1

Clear the learned power-on/off

signal from the button or label

(page 29).

2

Program the signal (transmitted

from the power-on/off button

of the air-conditioner

’

s remote

control) for the button or label

again.

3

Program the signal from the

same button of the remote

control for another button or

label.

The two buttons or labels of the

Commander have been

programmed with the power-on

signal and the power-off signal of

the air-conditioner, respectively so

that you can operate the air-

conditioner with the Commander.

If you make a mistake, move

the cursor to the digit or

character you want to correct

by pressing the

or

button,

and input again.

4

Decide the digit or the

character you input by

pressing the Joystick

toward

.

The cursor moves to the right.

When the Joystick is pressed

toward

, the cursor moves to

the left. You can input a digit or

character to the place where

the cursor flashes.

5

Repeat Steps 3 and 4 until

you input a suitable name

to the label.

When the cursor reaches to the

right end, if the Joystick is

pressed toward

, the cursor

returns back to the left end.

6

Press the SET button.

The commander enters the

learning standby mode.

Using Non-Preset Remote

Control Operations

—

Learning Function (continued)

Section	Page
Table of Contents	4
Getting Started	6
Location and Function of Controls	6
Installing the Batteries	7
When to replace the batteries	7
Setting the Clock	8
Setting the clock for the first time after installing batteries	8
Adjusting the clock after setting the clock	11
Basic Operations	13
Setting the Code for Preset Audio and Visual Components	13
Setting a component code	13
Checking if the code number works	16
Finding a component code with the Search function	17
To clear the contents programmed for a specific component label	19
Operating Your Components with the Remote Commander	21
To control the volume	23
Using Non-Preset Remote Control Operations — Learning Function	23
Notes on learning the signals of an air-conditioner	28
For accurate learning	29
Changing or erasing the function of a taught label or button	29
Advanced Features	30
Controlling the Volume of Visual Components Connected to an Audio System	30
Executing a Series of Commands — System Control Functions	34
Programming a series of commands for the System Macro labels	34
Notes on System Control Operations	38
To clear programmed commands for a specific System Macro number label	39
Programming a series of commands for the component labels	40
Changing the interval between operation steps	42
Changing the component macro executing time	43
Adding an Extra Function to the Component Labels	44
Programming the Power-On command of a selected component (for Sony components only)	44
Assigning Other Components to the Component Labels	46
Copying the settings of a component label to another label	46
Selecting a Channel with a Single Label — Channel Macro Function	48
Setting the Timer	51
Setting the new timer program	51
Changing the program already set or changing another program that you select	56
To clear timer settings programmed for a specific program number label	60
Using Other Functions	62
Locking the Controls — Hold Function	62
Adjusting the Automatic-Off Time of the Backlight of the Display Window	63
Setting the Key-Touch Beep	64
Adjusting the Contrast of the Display Window	65
Changing the Names of the Labels on the Display	65
Erasing All the Settings	68
Additional Information	70
Precautions	70
Maintenance	70
Specifications	70
Troubleshooting	71
Appendix	74
Table of Preset Functions	74
TV	74
SAT (Digital Satellite)	75
Digital cable box	76
DVD	77
VCR1, VCR2	78
DVR (Digital video recorder)	79
CD	80
CABLE (Cable box)	80
AMP	81
MD	82
DAT	82
TAPE A, TAPE B	83

Sony RM-VL1000 Operating Instructions - Page 28

Notes on learning the signals of an air-conditioner, Repeat Steps 3 and 4 until

Page 28 highlights