Sony VPL-FHZ65 Operating Instructions - Page 53

Symptom, Remedy, The settings for Brightness, Contrast, and Light Output

Get Sony VPL-FHZ65 PDF manuals and user guides View all Sony VPL-FHZ65 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

Symptom Edges of the image are cut off or dark. The image is distorted. The image is dark/too bright. The image is not clear. The image is noisy. No sound. The Remote Commander does not work. The fan is noisy. Remedy Page If you use the lens shift function with a setting outside the 65 recommended range, edges of the image may be cut off or appear dark. Use a setting within the normal range for the lens shift function. Warping is set. Disable the warp correction feature. 20, 36 The settings for "Brightness," "Contrast," and "Light Output 25 Mode" affect brightness of the image. Check if the value is appropriate. "With Static Signal" is set to "On." 35 When video signal is not input, the light is dimmed to reduce 34 power consumption. When the temperature around the unit is high, the brightness - will be reduced to protect the unit. Check if the projector is in focus. 18 The picture will not be clear if condensation has accumulated - on the lens. In such a case, let the projector sit for about two hours with the power on. Check if the connecting cable is connected to external 9 equipment properly. Check that the connecting cables between the projector and 9 external video or audio equipment are securely connected. Check if the output setting of connected external audio - equipment is set for output the audio signal from the projector. Audio is not output if audio muting is activated. 7 Check if the "Audio Output Vol." is set to minimum. 31 Check that the batteries are installed correctly. - Check that the batteries are not exhausted. - Check if the "ID Mode" of the projector corresponds to that of 8, 32 the Remote Commander. Check the setting for "IR Receiver." 32 The sound from the fan is often greater than normal to cool the light source in the following cases. • When "Light Output Mode" is set to "Standard." • The projector is in at high altitude ("High Altitude Mode" is set to "On") • Temperature is very high. 25, 37 • Check that the air filter is clogged, then clean or replace it. 4 • Check that the ventilation holes (intake/exhaust) are not blocked by a wall or an object and secure a sufficient gap. 53

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
53
Edges of the image are
cut off or dark.
If you use the lens shift function with a setting outside the
recommended range, edges of the image may be cut off or
appear dark. Use a setting within the normal range for the lens
shift function.
65
The image is distorted.
Warping is set.
Disable the warp correction feature.
20, 36
The image is dark/too
bright.
The settings for “Brightness,” “Contrast,” and “Light Output
Mode” affect brightness of the image. Check if the value is
appropriate.
25
“With Static Signal” is set to “On.”
35
When video signal is not input, the light is dimmed to reduce
power consumption.
34
When the temperature around the unit is high, the brightness
will be reduced to protect the unit.
–
The image is not clear.
Check if the projector is in focus.
18
The picture will not be clear if condensation has accumulated
on the lens. In such a case, let the projector sit for about two
hours with the power on.
–
The image is noisy.
Check if the connecting cable is connected to external
equipment properly.
9
No sound.
Check that the connecting cables between the projector and
external video or audio equipment are securely connected.
9
Check if the output setting of connected external audio
equipment is set for output the audio signal from the projector.
–
Audio is not output if audio muting is activated.
7
Check if the “Audio Output Vol.” is set to minimum.
31
The Remote
Commander does not
work.
Check that the batteries are installed correctly.
–
Check that the batteries are not exhausted.
–
Check if the “ID Mode” of the projector corresponds to that of
the Remote Commander.
8, 32
Check the setting for “IR Receiver.”
32
The fan is noisy.
The sound from the fan is often greater than normal to cool the
light source in the following cases.
• When “Light Output Mode” is set to “Standard.”
• The projector is in at high altitude (“High Altitude Mode” is
set to “On”)
• Temperature is very high.
25, 37
• Check that the air filter is clogged, then clean or replace it.
• Check that the ventilation holes (intake/exhaust) are not
blocked by a wall or an object and secure a sufficient gap.
4
Symptom
Remedy
Page