Sony WX-4500X Operating Instructions - Page 25

Troubleshooting - problem

Get Sony WX-4500X - Changer Control Audio Master PDF manuals and user guides View all Sony WX-4500X manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

Supplied accessories Optional accessories Optional equipment Parts for installation and connections (1 set) Rotary commander RM-X4S Card remote commander RM-X114 BUS cable (supplied with an RCA pin cord) RC-61 (1 m), RC-62 (2 m) CD changer (10 discs) CDX-848X, CDX-747X, CDX-646X MD changer (6 discs) MDX-65 Source selector XA-C30 Note This unit cannot be connected to a digital preamplifier or an equalizer. Design and specifications are subject to change without notice. Troubleshooting The following checklist will help you remedy problems you may encounter with your unit. Before going through the checklist below, check the connection and operating procedures. General No sound. • Rotate the jog roller upward to adjust the volume. • Cancel the ATT function. • Set the fader control to the center position for a 2-speaker system. • When using the optional Sony MD changer, an MD recorded in LP mode is being played. ("LP: ···" is shown in the display.) The contents of the memory have been erased. • The reset button has been pressed. t Store again into the memory. • The power cord or battery has been disconnected. • The power connecting cord is not connected properly. No beep sound. • The beep sound is canceled (page 19). • An optional power amplifier is connected and you are not using the built-in amplifier. Indications disappear from/do not appear in the display. • The clock display disappears if you press (OFF) for 2 seconds. t Press (OFF) again for 2 seconds to display the clock. • The Display is set to "off" (page 19). Stored stations and correct time are erased. The fuse has blown. Makes noise when the ignition key is in the ON, ACC, or OFF position. The leads are not matched correctly with the car's accessory power connector. No power is being supplied to the unit. • Check the connection. If everything is in order, check the fuse. • The car does not have an ACC position. t Press (SOURCE) (or insert a CD or cassette) to turn on the unit. The power is continuously supplied to the unit. The car does not have an ACC position. t Press (OFF) for 2 seconds. The power antenna does not extend. The power antenna does not have a relay box. 25 continue to next page t

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
25
Supplied accessories
Parts for installation and
connections (1 set)
Optional accessories
Rotary commander
RM-X4S
Card remote commander
RM-X114
BUS cable (supplied with
an RCA pin cord)
RC-61 (1 m), RC-62 (2 m)
Optional equipment
CD changer (10 discs)
CDX-848X, CDX-747X,
CDX-646X
MD changer (6 discs)
MDX-65
Source selector
XA-C30
Note
This unit cannot be connected to a digital preamplifier
or an equalizer.
Design and specifications are subject to change
without notice.
Troubleshooting
The following checklist will help you remedy
problems you may encounter with your unit.
Before going through the checklist below, check
the connection and operating procedures.
General
No sound.
• Rotate the jog roller upward to adjust the
volume.
• Cancel the ATT function.
•
Set the fader control to the center position for
a 2-speaker system.
• When using the optional Sony MD changer,
an MD recorded in LP mode is being played.
(“LP: ···” is shown in the display.)
The contents of the memory have been
erased.
• The reset button has been pressed.
t
Store again into the memory.
• The power cord or battery has been
disconnected.
• The power connecting cord is not connected
properly.
No beep sound.
• The beep sound is canceled (page 19).
• An optional power amplifier is connected
and you are not using the built-in amplifier.
Indications disappear from/do not appear in
the display.
• The clock display disappears if you press
(OFF)
for 2 seconds.
t
Press
(OFF)
again for 2 seconds to
display the clock.
• The Display is set to “off” (page 19).
Stored stations and correct time are erased.
The fuse has blown.
Makes noise when the ignition key is in the
ON, ACC, or OFF position.
The leads are not matched correctly with the
car’s accessory power connector.
No power is being supplied to the unit.
• Check the connection. If everything is in
order, check the fuse.
• The car does not have an ACC position.
t
Press
(SOURCE)
(or insert a CD or
cassette) to turn on the unit.
The power is continuously supplied to the
unit.
The car does not have an ACC position.
t
Press
(OFF)
for 2 seconds.
The power antenna does not extend.
The power antenna does not have a relay box.
continue to next page
t