Sony WX-4500X Operating Instructions - Page 26

CD/MD playback, Tape playback, Radio reception, Set the Dolby NR to off - wiring

Get Sony WX-4500X - Changer Control Audio Master PDF manuals and user guides View all Sony WX-4500X manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

Cannot turn off the "--------" indication. You entered the name edit mode. t Push the jog roller or press (LIST) on the card remote commander for 2 seconds. "ATT" appears in the display, and volume is reduced. The telephone ATT control lead is shorting on a metal part of the car. t Insulate any exposed wires with electrical tape to avoid any short circuit. CD/MD playback A disc cannot be loaded. • Another CD/MD is already loaded. • The CD/MD is forcibly inserted upside down or in the wrong way. Playback does not begin. • Defective MD or dirty CD. • CD-R/CD-RW that is not finalized. • You tried to playback a CD-R/CD-RW not designed for audio use. • Some CD-Rs/CD-RWs may not play due to its recording equipment or the disc condition. A disc is automatically ejected. The ambient temperature exceeds 50°C (122°F). The operation buttons do not function. CD will not be ejected. Press the reset button. The sound skips from vibration. • The unit is installed at an angle of more than 30°. • The unit is not installed in a sturdy part of the car. The sound skips. Dirty or defective disc. Tape playback The sound is distorted. • The tape head is contaminated. t Clean the head with a commercially available dry-tape cleaning cassette. • A tape recorded with Dolby NR off is played back with Dolby NR on. t Set the Dolby NR to "off" (page 14). The AMS does not operate correctly. • There is noise in the space between tracks. • A blank space is too short (less than 4 seconds). • A long pause, or a passage of low frequencies or very low sound level is treated as a blank space. Radio reception Preset tuning is not possible. • Store the correct frequency in the memory. • The broadcast signal is too weak. The stations cannot be received. The sound is hampered by noises. • Connect a power antenna control lead (blue) or accessory power supply lead (red) to the power supply lead of a car's antenna booster. (Only when your car has built-in FM/AM antenna in the rear/side glass.) • Check the connection of the car antenna. • The auto antenna will not go up. t Check the connection of the power antenna control lead. • Check the frequency. • When the DSO mode is on, the sound is sometimes hampered by noises. t Set the DSO mode to "off" (page 20). Automatic tuning is not possible. • The local seek mode is set to "on." t Set the local seek mode to "off" (page 20). • The broadcast signal is too weak. t Perform manual tuning. The "ST" indication flashes. • Tune in the frequency accurately. • The broadcast signal is too weak. t Set to the monaural reception mode (page 20). A program broadcast in stereo is heard in monaural. The unit is in monaural reception mode. t Cancel monaural reception mode (page 20). Interference occurs during FM reception. The wide mode is selected. t Set the IF mode to "IF Auto" (page 20). 26

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
26
Cannot turn off the “--------” indication.
You entered the name edit mode.
t
Push the jog roller or press
(LIST)
on the
card remote commander for 2 seconds.
“ATT” appears in the display, and volume is
reduced.
The telephone ATT control lead is shorting on
a metal part of the car.
t
Insulate any exposed wires with electrical
tape to avoid any short circuit.
CD/MD playback
A disc cannot be loaded.
• Another CD/MD is already loaded.
•
The CD/MD is forcibly inserted upside down
or in the wrong way.
Playback does not begin.
• Defective MD or dirty CD.
• CD-R/CD-RW that is not finalized.
• You tried to playback a CD-R/CD-RW not
designed for audio use.
• Some CD-Rs/CD-RWs may not play due to
its recording equipment or the disc
condition.
A disc is automatically ejected.
The ambient temperature exceeds 50°C
(122°F).
The operation buttons do not function.
CD will not be ejected.
Press the reset button.
The sound skips from vibration.
• The unit is installed at an angle of more than
30°.
• The unit is not installed in a sturdy part of
the car.
The sound skips.
Dirty or defective disc.
Tape playback
The sound is distorted.
• The tape head is contaminated.
t
Clean the head with a commercially
available dry-tape cleaning cassette.
•
A tape recorded with Dolby NR off is played
back with Dolby NR on.
t
Set the Dolby NR to “off” (page 14).
The AMS does not operate correctly.
• There is noise in the space between tracks.
• A blank space is too short (less than 4
seconds).
• A long pause, or a passage of low
frequencies or very low sound level is treated
as a blank space.
Radio reception
Preset tuning is not possible.
• Store the correct frequency in the memory.
• The broadcast signal is too weak.
The stations cannot be received.
The sound is hampered by noises.
• Connect a power antenna control lead (blue)
or accessory power supply lead (red) to the
power supply lead of a car’s antenna booster.
(Only when your car has built-in FM/AM
antenna in the rear/side glass.)
• Check the connection of the car antenna.
• The auto antenna will not go up.
t
Check the connection of the power
antenna control lead.
• Check the frequency.
• When the DSO mode is on, the sound is
sometimes hampered by noises.
t
Set the DSO mode to “off” (page 20).
Automatic tuning is not possible.
• The local seek mode is set to “on.”
t
Set the local seek mode to “off” (page
20).
• The broadcast signal is too weak.
t
Perform manual tuning.
The “ST” indication flashes.
• Tune in the frequency accurately.
• The broadcast signal is too weak.
t
Set to the monaural reception mode (page
20).
A program broadcast in stereo is heard in
monaural.
The unit is in monaural reception mode.
t
Cancel monaural reception mode (page
20).
Interference occurs during FM reception.
The wide mode is selected.
t
Set the IF mode to “IF Auto” (page 20).