Stihl MS 180 C-BE Product Instruction Manual - Page 38

Operating Instructions

Get Stihl MS 180 C-BE PDF manuals and user guides View all Stihl MS 180 C-BE manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

English Operating Instructions During the break-in period A factory new machine should not be run at high revs (full throttle off load) for the first three tank fillings. This avoids unnecessarily high loads during the break-in period. As all moving parts have to bed in during the break-in period, the frictional resistances in the shortblock are greater during this period. The engine develops its maximum power after about 5 to 15 tank fillings. During work Do not make the mixture leaner to achieve an apparent increase in power - this could damage the engine - see "Adjusting the Carburetor". Open the throttle only when the chain brake is off. Running the engine at high revs with the chain brake engaged (chain locked) will quickly damage the shortblock and chain drive (clutch, chain brake). Check chain tension frequently A new saw chain must be retensioned more frequently than one that has been in use already for an extended period. Chain cold Tension is correct when the chain fits snugly against the underside of the bar but can still be pulled along the bar by hand. Retension if necessary - see "Tensioning the Saw Chain". Chain at operating temperature The chain stretches and begins to sag. The drive links must not come out of the bar groove on the underside of the bar - the chain may otherwise jump off the bar. Retension the chain - see "Tensioning the Saw Chain". The chain contracts as it cools down. If it is not slackened off, it can damage the crankshaft and bearings. After a long period of full-throttle operation After a long period of full-throttle operation, allow engine to run for a while at idle speed so that the heat in the engine can be dissipated by flow of cooling air. This protects enginemounted components (ignition, carburetor) from thermal overload. After finishing work N Slacken off the chain if you have retensioned it at operating temperature during work. Always slacken off the chain again after finishing work. The chain contracts as it cools down. If it is not slackened off, it can damage the crankshaft and bearings. Short-term storage Wait for engine to cool down. Keep the machine with a full tank of fuel in a dry place, well away from sources of ignition, until you need it again. Long-term storage See "Storing the machine" 36 MS 170, MS 170 C, MS 180, MS 180 C

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
MS 170, MS 170 C, MS 180, MS 180 C
English
36
During the break-in period
A factory new machine should not be run
at high revs (full throttle off load) for the
first three tank fillings. This avoids
unnecessarily high loads during the
break-in period. As all moving parts
have to bed in during the break-in
period, the frictional resistances in the
shortblock are greater during this period.
The engine develops its maximum
power after about 5 to 15 tank fillings.
During work
Check chain tension frequently
A new saw chain must be retensioned
more frequently than one that has been
in use already for an extended period.
Chain cold
Tension is correct when the chain fits
snugly against the underside of the bar
but can still be pulled along the bar by
hand. Retension if necessary – see
"Tensioning the Saw Chain".
Chain at operating temperature
The chain stretches and begins to sag.
The drive links must not come out of the
bar groove on the underside of the bar –
the chain may otherwise jump off the
bar. Retension the chain – see
"Tensioning the Saw Chain".
After a long period of full-throttle
operation
After a long period of full-throttle
operation, allow engine to run for a while
at idle speed so that the heat in the
engine can be dissipated by flow of
cooling air. This protects engine-
mounted components (ignition,
carburetor) from thermal overload.
After finishing work
N
Slacken off the chain if you have
retensioned it at operating
temperature during work.
Short-term storage
Wait for engine to cool down. Keep the
machine with a full tank of fuel in a dry
place, well away from sources of
ignition, until you need it again.
Long-term storage
See "Storing the machine"
Operating Instructions
Do not make the mixture leaner to
achieve an apparent increase in
power – this could damage the
engine – see "Adjusting the
Carburetor".
Open the throttle only when the
chain brake is off. Running the
engine at high revs with the chain
brake engaged (chain locked) will
quickly damage the shortblock
and chain drive (clutch, chain
brake).
The chain contracts as it cools
down. If it is not slackened off, it
can damage the crankshaft and
bearings.
Always slacken off the chain again
after finishing work. The chain
contracts as it cools down. If it is
not slackened off, it can damage
the crankshaft and bearings.