TP-Link TD-W8960N User Guide - Page 35

ATM-IPoA, 1P Priority, 1Q VLAN ID - . user manual

Get TP-Link TD-W8960N PDF manuals and user guides
UPC - 845973060343
View all TP-Link TD-W8960N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

TD-W8960N Wireless N ADSL2+ Modem Router User Guide 4.4.2.5 ATM-IPoA If your ISP provides an IPoA connection and you need to use an ATM Interface, follow the steps below to add a WAN service over a selected ATM interface. 1. Add a new ATM interface and select IPoA option for DSL Link Type (see 4.4.1.1 ATM interface). 2. Click the Add button on the screen Figure 4-7 and the next configuration is similar to IPoE (see section 4.4.2.2 ATM-EoA-IPoE). The difference is that you have to manually set the Static IP Address on the screen of Figure 4-15, and the Static IP Address for DNS Server on the screen of Figure 4-18. ) Note: ETH and ATM service can not coexist. If the ATM Interface had configured, you cannot configure any other WAN service over the ETH Interface until the ATM Interface is deleted. 4.4.2.6 ETH-PPPoE If your ISP provides a PPPoE connection and you need to use an ETH Interface, follow the steps below to add a WAN service over a selected ETH interface: 1. Add a new ETH interface on the screen of 4.4.1.2 ETH interface. 2. Click the Add button on the screen Figure 4-7 and the following configuration is similar to PPPoE over ATM interface (see section 4.4.2.1 ATM-EoA-PPPoE). 4.4.2.7 ETH-IPoE If your ISP provides an IPoE connection and you want to use an ETH Interface, follow the steps below to add a WAN service over a selected ETH interface: 1. Add a new ETH interface on the screen of 4.4.1.2 ETH interface. 2. Click the Add button on the screen Figure 4-7 and the next configuration is similar to IPoE over ATM interface (see section 4.4.2.2 ATM-EoA-IPoE). 4.4.2.8 ETH-Bridge If you want to adopt the Bridge service and you need to use an ETH Interface, follow the steps below to add a WAN service over a selected ETH interface: 1. Add a new ETH interface on the screen of 4.4.1.2 ETH interface. 2. Click the Add button on the screen Figure 4-7 and the next configuration is similar to Bridge over ATM interface (see section 4.4.2.3 ATM-EoA-Bridg). ) Note: For ETH-PPPoE, ETH-IPoE and ETH-Bridge, the Bridging option will display in the screen of Figure 4-20 only when VLAN MUX Mode is selected for Connection Mode on the screen of Figure 4-5. You have to set the 802.1P Priority and 802.1Q VLAN ID. 28

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
TD-W8960N
Wireless N ADSL2+ Modem Router User Guide
4.4.2.5 ATM-IPoA
If your ISP provides an
IPoA
connection and you need to use an ATM Interface, follow the steps
below to add a WAN service over a selected ATM interface.
1.
Add a new ATM interface and select
IPoA
option for DSL Link Type (see
4.4.1.1
ATM
interface
).
2.
Click the
Add
button on the screen Figure 4-7 and the next configuration is similar to
IPoE
(see section
4.4.2.2
ATM-EoA-IPoE
). The difference is that you have to manually set the
Static IP Address on the screen of Figure 4-15, and the Static IP Address for DNS Server on
the screen of Figure 4-18.
)
Note:
ETH and ATM service can not coexist. If the ATM Interface had configured, you cannot configure
any other WAN service over the ETH Interface until the ATM Interface is deleted.
4.4.2.6 ETH-PPPoE
If your ISP provides a
PPPoE
connection and you need to use an
ETH
Interface, follow the steps
below to add a WAN service over a selected ETH interface:
1.
Add a new
ETH
interface on the screen of
4.4.1.2
ETH interface
.
2.
Click the
Add
button on the screen Figure 4-7 and the following configuration is similar to
PPPoE
over ATM interface
(see section
4.4.2.1
ATM-EoA-PPPoE
).
4.4.2.7 ETH-IPoE
If your ISP provides an
IPoE
connection and you want to use an
ETH
Interface, follow the steps
below to add a WAN service over a selected ETH interface:
1.
Add a new
ETH
interface on the screen of
4.4.1.2
ETH interface
.
2.
Click the
Add
button on the screen Figure 4-7 and the next configuration is similar to
IPoE
over ATM interface
(see section
4.4.2.2
ATM-EoA-IPoE
).
4.4.2.8 ETH-Bridge
If you want to adopt the
Bridge
service and you need to use an
ETH
Interface, follow the steps
below to add a WAN service over a selected ETH interface:
1.
Add a new
ETH
interface on the screen of
4.4.1.2
ETH interface
.
2.
Click the
Add
button on the screen Figure 4-7 and the next configuration is similar to
Bridge
over ATM interface
(see section
4.4.2.3
ATM-EoA-Bridg
).
)
Note:
For ETH-PPPoE, ETH-IPoE and ETH-Bridge, the Bridging option will display in the screen of
Figure 4-20 only when VLAN MUX Mode is selected for Connection Mode
on the screen of Figure
4-5. You have to set the
802.1P Priority
and
802.1Q VLAN ID
.
28