TP-Link TD-W8960N User Guide - Page 39

NAT - dropping connection

Get TP-Link TD-W8960N PDF manuals and user guides
UPC - 845973060343
View all TP-Link TD-W8960N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

TD-W8960N Wireless N ADSL2+ Modem Router User Guide The WAN Interface List displays the Lay2 Interfaces you have configured on the section 4.4.1 Layer2 Interface and its default MAC Address. If you have not configured corresponding WAN Service for the interface on the section 4.4.2 WAN Service, the blank for MAC Address will display "Need a corresponding WAN Service". The last one of WAN Interface List displays your PC's current address. Figure 4-23 Type the new value for the WAN Interface who's MAC Address you want to change, and click Save/Apply. You can select corresponding WAN Interface from the drop-down list and click Clone button to clone your current PC MAC, and then click Save/Apply. Click Restore Default button to restore the WAN Interface's default MAC Address. ) Note: Only the WAN Ports can use MAC Address Clone function. All the clone MAC addresses must not be the same with each other. 4.4.5 NAT NAT (Network Address Translation) allows you to share one WAN (Wide Area Network) IP address for multiple computers on your LAN (Local Area Network). ) Note: When you select PPPoA or PPPoE for the WAN Setup, or when you select Enable NAT for the type of IPoA and IPoE connection (4.4.2 WAN Service), you will see the NAT menu in the Web-based Utility (shown in Figure 4-24). Choose "Advanced Setup"Æ"NAT", there are three submenus under the main menu: Virtual Servers, Port Triggering and DMZ Host. Click any of them, and you will be able to configure the corresponding function. 32

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
TD-W8960N
Wireless N ADSL2+ Modem Router User Guide
The WAN Interface List displays the Lay2 Interfaces you have configured on the section
4.4.1
Layer2 Interface
and its default MAC Address. If you have not configured corresponding WAN
Service for the interface on the section
4.4.2
WAN Service
, the blank for MAC Address will display
“Need a corresponding WAN Service”.
The last one of WAN Interface List displays your PC’s current address.
Figure 4-23
Type the new value for the WAN Interface who’s MAC Address you want to change, and click
Save/Apply
.
You can select corresponding WAN Interface from the drop-down list and click
Clone
button to
clone your current PC MAC, and then click
Save/Apply
.
Click
Restore Default
button to restore the WAN Interface’s default MAC Address.
)
Note:
Only the WAN Ports can use MAC Address Clone function. All the clone MAC addresses must not
be the same with each other.
4.4.5 NAT
NAT (Network Address Translation) allows you to share one WAN (Wide Area Network) IP
address for multiple computers on your LAN (Local Area Network).
)
Note:
When you select
PPPoA
or
PPPoE
for the WAN Setup, or when you select
Enable NAT
for the
type of
IPoA
and
IPoE
connection (
4.4.2
WAN Service
), you will see the
NAT
menu in the
Web-based Utility (shown in Figure 4-24).
Choose “
Advanced Setup
”
Æ
“
NAT
”, there are three submenus under the main menu
: Virtual
Servers
,
Port Triggering
and
DMZ Host
. Click any of them, and you will be able to configure the
corresponding function.
32