TRENDnet TEW-841APBO Users Guide - Page 7

Power PWR LED, Important Note

Get TRENDnet TEW-841APBO PDF manuals and user guides View all TRENDnet TEW-841APBO manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

TRENDnet User's Guide  4 x RP-SMA (female) antenna connectors - The access point ships with 4 x 5dBi Omni directional antennas. Please take note to connect the correct antenna, the antennas are tuned for optimizations on their labeled wireless bands.  Waterproof kit - The access point comes with a waterproof cable guard for outdoor installations.  Mounting Point - The access point can be wall or pole mounted using the mounting points on the unit, and the mounting kit included with the packaging.  PoE+ Gigabit LAN port (power input) - This gigabit Ethernet interface will be used to power the access point using standard 802.11at PoE+ power source and provide gigabit network connectivity to the access point.  Power (PWR) LED - When the LED is ON, this will indicate that the device is receiving power and OFF if the device is not receiving power.  LAN LED - When the LED is ON, this indicates an active network connection to the LAN port on the proprietary PoE injector. When the LED is BLINKING, this indicates data is being transmitted or received on the LAN port.  2.4GHz LED - When the LED is ON, the wireless radio on the device is on. When the LED is OFF, the wireless radio on the device has been disabled.  5GHz LED - When the LED is ON, the wireless radio on the device is on. When the LED is OFF, the wireless radio on the device has been disabled. Important Note: It is recommended to use RJ-45 cables without any additional caps, molded caps, or boots specifically on the connector side that will be connected to the access point LAN1 (PoE) port to avoid any cable fitment issues. © Copyright 2019 TRENDnet. All Rights Reserved. TEW-841APBO 4

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
© Copyright 2019 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-841APBO
4
4 x RP-SMA (female) antenna connectors
–
The access point ships with 4 x 5dBi
Omni directional antennas. Please take note to connect the correct antenna,
the antennas are tuned for optimizations on their labeled wireless bands.
Waterproof kit
–
The access point comes with a waterproof cable guard for
outdoor installations.
Mounting Point
–
The access point can be wall or pole mounted using the
mounting points on the unit, and the mounting kit included with the packaging.
PoE+ Gigabit LAN port (power input)
–
This gigabit Ethernet interface will be
used to power the access point using standard 802.11at PoE+ power source
and provide gigabit network connectivity to the access point.
Power (PWR) LED
–
When the LED is ON, this will indicate that the device is
receiving power and OFF if the device is not receiving power.
LAN LED
–
When the LED is ON, this indicates an active network connection to
the LAN port on the proprietary PoE injector. When the LED is BLINKING, this
indicates data is being transmitted or received on the LAN port.
2.4GHz LED
–
When the LED is ON, the wireless radio on the device is on. When
the LED is OFF, the wireless radio on the device has been disabled.
5GHz LED
–
When the LED is ON, the wireless radio on the device is on. When
the LED is OFF, the wireless radio on the device has been disabled.
Important Note:
It is recommended to use RJ-45 cables without any additional caps, molded caps, or
boots specifically on the connector side that will be connected to the access point LAN1
(PoE) port to avoid any cable fitment issues.