Home » Thermador Manuals » Dishwashers » Thermador DWHD770WFM » Manual Viewer

Thermador DWHD770WFM Instructions for Use - Page 15

Using detergents with salt component, Switching off low salt indicator / water, softening system

View all Thermador DWHD770WFM manuals

Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

Using detergents with salt component Detrgnwithasltcompnet If combined detergents with a salt component are used, special salt can usually be omitted up to a water hardness of 21° dH (37° fH, 26° Clarke, 3.7 mmol/l). If the water hardness is over 21° dH, salt must be used. Switching off low salt indicator / water softening system Switchngofwatersofnigsytem If the use of combined detergents with a salt component impairs the low salt indicator P on the control panel or the text on the display window at the top @ (enough salt for x rinse cycles), the displays can be switched off. Proceed as described under "Setting water softening system" and set the value to 0-8. The water softening system and salt refill indicator are now switched off. 15

Section	Page
Table of contentsen-us Operating instructions	3
Safety Definitions	3
9 WARNING	3
9 CAUTION	3
NOTICE:	3
Note:	3
IMPORTANT SAFETY INSTRUCTIONS	4
READ AND SAVE THESE INSTRUCTIONS	4
To reduce the risk of fire, electrical shock, or serious injury, observe the following:Risk of fire, electrical shock, or serious injury	4
WARNING	4
Risk of injury or death	4
WARNING	4
Risk of injury	4
WARNING	4
Risk of electrical shock or fire	4
WARNING	4
WARNING	4
Health hazard	4
GROUNDING INSTRUCTIONS	5
WARNING	5
Risk of electric shock	5
Safe Operation	5
CAUTION	5
WARNING	5
WARNING	5
Proper Care and Maintenance	6
Note:	6
NOTICE:	6
Proposition 65 Warning:	6
Causes of Damage	7
NOTICES	7
Getting Started	8
Appliance overview	8
Operating panel	9
Dishwasher interior components	9
Display indicators	9
Info button (Info button	9
1. Press the Info button ( 8.	9
2. Press the wash cycle button.	9
3. To leave, press Info button ( 8.	9
Switching on the appliance for the first time	10
Change the setting as follows:	10
1. Keep pressing button > ` until the required setting is displayed.	10
2. Make the selection with setting buttons + - X.	10
3. Press and hold the Info button ( 8 for 3 seconds.	10
Settings	11
Change the setting as follows:	11
1. Open the door.	11
2. Switch on ON/OFF switch (.	11
3. Press Info button ( 8 for 3 seconds until the following text is indicated on the display window at the top @:	11
4. Keep pressing button > ` until the required setting is displayed.	11
5. Make the selection with setting buttons + - X.	11
6. Press and hold the Info button ( 8 for 3 seconds.	11
Note:	11
Home Connect™ System	12
Info buttonInfo button	12
1. Press the Info button 8.	12
2. Press the wash cycle button.	12
3. To leave, press Info button 8.	12
Setting up the app	12
Setting up Home Connect	12
1. Open the door.	12
2. Switch on the On/Off switch (.	12
3. Press Info button 8 for 3 seconds until the following text is indicated on the display window at the top @:	12
4. Keep pressing button > h until the required setting is indicated on the display window at the top @.	12
5. Make the setting with setting buttons + - X. See table in section	12
6. Press and hold the Info button 8 for 3 seconds.	12
Wi-Fi \|	12
Notes	12
Network login	12
Connect to App	12
Remote start button	13
Note:	13
Notes	13
Wi-Fi without a connection to the Home Connect server ƒWi-Fi without a connection to the Home Connect server	13
Note:	13
Remote diagnosis ~Remote diagnosis	13
Notes	13
Water softening system / special salt	14
Water hardness table	14
Using a water hardness test strip	14
Sample test strip	14
Adjusting the water softening system	14
Set the softening system as follows:	14
1. Ask your local water utility company for the water hardness value of the tap water.	14
2. Required setting can be found in the water hardness table.	14
3. Open the door.	14
4. Switch on ON/OFF switch (.	14
5. Press Info button ( 8 for 3 seconds until the following text is indicated on the display window at the top @:	14
6. Keep pressing button > ` until the water hardness is indicated on the display window at the top @.	14
7. Make the selection with setting buttons + - X.	14
8. Press and hold the Info button ( 8 for 3 seconds.	14
Using special salt	14
NOTICE:	14
Top off the salt as follows:	14
1. Undo the screw plug on the dispenser 1b.	14
2. Fill the dispenser with water (required only when switching on the appliance for the first time).	14
3. Add salt as illustrated (do not use table salt or tablets).	14
Using detergents with salt componentDetergent with a salt component	15
Switching off low salt indicator / water softening systemSwitching off water softening system	15
Rinse Aid	16
Adding rinse aid	16
NOTICE:	16
1. Open the rinse aid dispenser 92 by pressing on the latch of the lid and pulling it open.	16
2. Add liquid rinse aid to the dispenser 92 until it is full. Do not overfill. Avoid spilling into air vent hole.	16
3. Close the lid. Lid must be fully closed until it clicks in order to seal.	16
4. Wipe up any excess rinse aid that may have puddled when the dispenser reservoir is full.	16
Tip:	16
NOTICE:	16
Setting the amount of rinse aid used	16
Set the amount of rinse aid as follows:	16
1. Open the door.	16
2. Press on ON/OFF button (.	16
3. Press Info button ( 8 for 3 seconds until the following text is indicated on the display window at the top @:	16
4. Keep pressing button > ` until the rinse aid dispenser is indicated on the display window at the top @.	16
5. Make the selection with setting buttons + - X.	16
6. Press and hold the Info button ( 8 for 3 seconds.	16
Note:	16
Switching off rinse aid refill indicator	16
NOTICE:	16
Loading the Dishwasher	17
Dishware material	17
Note:	17
Loading the racks	17
NOTICE:	17
Loading the upper rack	17
Note:	17
Loading the lower rack	17
Loading patterns	18
Loading patterns for lower rack	18
12 place setting suggested loading pattern	18
Alternate loading pattern	18
Alternate loading pattern with pots and pans	18
Alternate loading with stemware *	18
Loading patterns for upper rack	19
12 place setting suggested loading pattern, with cutlery drawer	19
12 place setting suggested loading with Entertainer’s Drawer	19
Alternate loading pattern	19
Alternate loading pattern with stemware	19
Loading patterns for third rack	19
12 place setting suggested loading pattern *	19
Third rack 1*	19
Loading the silverware basket	20
9 WARNING	20
Risk of injury	20
The Double Flex silverware basket	20
Side by side	20
Back to back	20
Note:	20
Loading patterns silverware basket	21
Suggested loading pattern with Entertainer’s Drawer - 12 place setting	21
Alternate loading pattern	21
Unloading the dishwasher	21
9 CAUTION	21
Note:	21
RackMatic® System	21
1. Pull the upper rack out of the dishwasher until it stops.	21
2. To lower the rack, push the RackMatic® lever inward.	21
3. To raise the rack, hold the basket on the sides of the upper rack and lift it up.	21
Note:	21
Adjusting the height of the rack *Adjusting the height of the rack	22
9.4 in (24 cm)	22
13.4 in (34 cm)	22
10.4 in (26.5 cm)	22
12 in (30.5 cm)	22
11.4 in (29 cm)	22
11 in (28 cm)	22
7 in (18 cm)	22
13.4 in (34 cm)	22
8 in (20.5 cm)	22
12 in (30.5 cm)	22
9 in (23 cm)	22
11 in (28 cm)	22
Rack accessories	22
Flip tines	22
Fold down the flip tines as follows:	22
1. Pull flip tine gently forward and release it from the notch (1).	22
2. Push the flip tine downward to the desired position (2).	22
Third rack*	22
Entertainer’s Drawer * 1*	23
Cup shelves	23
Extra tall item sprinkler	24
Note:	24
NOTICE:	24
Removing/Installing third rack	24
Removing third rack 1*	24
1. Pull out third rack all the way (1).	24
2. Lift upper rollers over the stopper hooks of both rails (2).	24
3. Pull third rack out forward and upward so that the holding hooks and the lower rollers of the rack slide over the stopper hooks of both rails (3).	24
Installing third rack 1*	24
1. Pull out third rack rails all the way (1).	24
2. Insert third rack at an angle. Make sure that the stopper hooks of both rails slide in between the holding hooks and the lower rollers of the third rack (2).	24
3. Slide third rack in and lift the upper rollers over the front stopper hooks of both rails (3).	24
4. Push in third rack (4).	24
Removing/Installing upper rack with Rackmatic®	25
Removing upper rack 12	25
1. Pull out upper rack all the way (1).	25
2. Lift front rollers over the stopper hook of the rail (2).	25
3. Pull out upper rack forwards and upwards so that the upper and lower rollers of the rack slide over the stopper hooks of both rails (3).	25
Installing upper rack 12	25
1. Pull out upper rack rails all the way (1).	25
2. Insert upper rack at an angle. Make sure that the stopper hooks of both rails slide in between the upper and lower rollers on the rear side of the rack (2).	25
3. Slide upper rack in and lift the upper rollers over the front stopper hooks of both rails (3).	25
4. Push in upper rack (4).	25
Detergent	26
NOTICE:	26
Note:	26
Adding detergent	26
1. If the detergent dispenser 9: is still closed, push the button 9B to open it.	26
Note:	26
2. When using detergent tabs, lay them such that they do not come in contact with the cover, insert a detergent tab flat, not on its side.	26
Note:	26
3. Close the lid by placing the finger on the lid as shown. Slide the lid closed and press down firmly until it clicks.	27
Tip:	27
Dishwasher Cycles	28
Note:	28
Note:	28
Dishwasher Cycle Options	29
PowerBoost ®	29
Save Time	29
Half Load	29
Sanitize	29
StarDry™	29
Wash Cycle Information	30
Note:	30
Operating the Dishwasher	31
Note:	31
9 WARNING	31
Risk of injury	31
Protection against unintentional operation	31
Note:	31
Operating the touch buttons	31
Changing the settings	31
Change the setting as follows:	31
1. Open the door.	31
2. Switch on On/Off button (.	31
3. Press Info button 8 for 3 seconds until the following text is indicated in the digital display @:	31
4. Keep pressing button > ` until the required setting is indicated in the display window at the top @.	31
5. Make the selection with setting buttons + - X.	31
6. Press and hold the Info button 8 for 3 seconds.	31
Tip:	31
AquaSensor	31
Time display	31
Sensor setting	31
Extra Dry	31
Eco forecast	31
Auto power off	32
Possible settings are:	32
Tone volume	32
Button volume	32
Greeting	32
Factory setting	32
Switching the appliance on	32
1. Turn the water supply on fully.	32
2. Open the door.	32
3. Switch on On/Off switch (.	32
4. Press Start button )*.	32
5. Close the door.	32
Note:	32
Delay start time	32
1. Open the door.	32
2. Switch on On/Off switch (.	32
3. Select wash cycle 0.	32
4. Press Delay start button `.	32
5. Keep pressing the setting buttons + - X until the displayed time corresponds with your requirements.	32
6. Press Start button )*, timer programming is activated.	32
7. To delete the Delay start time, press Start button )* for about 3 seconds.	32
8. Close the door.	32
Note:	32
Sapphire Glow (emotionLight™) *	32
Note:	32
Star Glow (emotionLight Pro™) *	32
Possible settings are:	32
Notes	32
Time Remaining Power Beam® (Optical display while the wash cycle is running)	33
Using the Star Speed® cycle	33
1. Open the door and press the ON/OFF button (	33
2. Press the Star Speed® button. The dishwasher should be empty and without detergent for the preheating period.	33
3. Press the Start button )* and close the door to begin preheating. The Time Remaining PowerBeam® will project an image of a thermometer alternating with the time remaining for preheat. Once the time reamining counts down to 0:00, the Time Remainin...	33
4. Open the door to begin loading dishes for the first Star Speed® wash. (Load dishes within an hour once the preheating is finished).	33
5. Add detergent (use powder or liquid detergent – do not use tablets in this cycle), press Start button )* and close the door within 4 seconds.	33
6. The Time Remaining PowerBeam® will now show the time remaining.	33
7. When the cycle is done, the Time Remaining PowerBeam® will turn off.	33
8. The next Star Speed® cycles can run without any preheating (maximum of 60 minutes in between cycles).	33
Wash cycle end	33
Switching off the appliance	33
Short time after the end of the wash cycle:	33
1. Press On/Off button (.	33
2. Remove the dishes when they have cooled down.	33
9 WARNING	33
Risk of injury	33
Interrupting the wash cycle	33
9 CAUTION	33
1. Open the door.	33
2. Switch off On/Off switch (.	33
3. To continue the wash cycle, switch on the On/Off switch ( again.	33
4. Close the door.	33
Note:	33
Cancel a cycle (reset)	33
1. Open the door and press and hold the Start button )* for approximately 3 seconds until the digital display @ shows: \	33
2. Close the door.	33
3. Wait about 1 minute while the dishwasher drains.	33
4. Open the door and press the On/Off switch (.	33
Changing the wash cycle	33
Care and Maintenance	34
Cleaning the dishwasher	34
NOTICES	34
9 WARNING	34
Filters	34
Filter components	34
The filter system 1j consists of three parts.	34
Cleaning intervals	34
Note:	35
To check or clean the filter system:	35
1. After each wash cycle check the filters for residue.	35
2. Unscrew the Large Object Trap as illustrated and remove the entire filter system.	35
3. Remove the microfilter from the fine filter for easier cleaning.	35
4. Rinse the filters under running water and use a soft brush to clean.	35
Note:	35
5. Reinstall the filter system in reverse sequence and lock into place by screwing the Large Object Trap until the marking arrows align.	35
Spray arms	35
1. Check outlet nozzles on the spray arms for blockages.	35
2. Unscrew the upper spray arm 1: (1) and remove downwards (2).	35
3. Remove the lower spray arm 1Z upwards.	35
4. Clean spray arms under running water.	35
5. Re-engage or screw on spray arms.	35
Drain pump	36
9 WARNING	36
1. Disconnect the appliance from the power supply.	36
2. Take out upper rack 12 and lower rack 9*.	36
3. Remove the filters 1j.	36
4. Scoop out standing water - use a sponge if necessary.	36
5. Using a spoon, pry off the pump cover (as shown) until it clicks, then grip the cover and pull upward until it resists and then pull forward (1). Remove cover completely.	36
6. Check inner compartment and remove any foreign objects.	36
7. Place pump cover in the original position (2) and press down until it engages (3).	36
8. Place cover in the original position, press down and engage.	36
9. Reinstall filters.	36
10. Re-insert racks.	36
Note:	36
Preparing your unit for vacation	36
NOTICE:	36
Winterizing your unit	36
NOTICE:	36
Troubleshooting	37
Note:	37
9 WARNING	37
Improper repairs or use of non-original replacement parts may cause considerable damage and put the user at considerable risk	37
Error message	37
Fault table	37
Customer Service	42
1. Contact your installer or the Thermador® authorized service provider in your area.	42
2. E-mail us from the customer service section of our website, www.thermador.com (USA) or www.thermador.ca (Canada)	42
3. Call us at 800-735-4328	42
4. Write us:	42
Statement of Limited Product Warranty	43
What this Warranty Covers & Who it Applies to:	43
How Long the Warranty Lasts	43
Extended Limited Warranty	43
Repair/Replace as Your Exclusive Remedy	43
Out of Warranty Product	43
Warranty Exclusions	44
How to Obtain Warranty Service	44
Table des matièresfr-ca Notice d'utilisation	45
Indications de sécurité	45
9 AVERTISSEMENT	45
9 ATTENTION	45
AVIS :	45
Remarque :	45
CONSIGNES DE SÉCURITÉ IMPORTANTES	46
LISEZ ET CONSERVEZ CES INSTRUCTIONS	46
Pour réduire le risque d'incendie, de choc électrique, ou de blessures graves, respectez les consignes suivantes :Risque d'incendie, de choc électrique, ou de blessures graves	46
AVERTISSEMENT	46
Risque de blessure ou de décès	46
AVERTISSEMENT	46
Risque de blessures	46
AVERTISSEMENT	46
Risque de choc électrique ou d'incendie	46
AVERTISSEMENT	46
AVERTISSEMENT	46
Risque pour la santè	46
INSTRUCTIONS DE MISE À LA TERRE	46
AVERTISSEMENT	46
Risque de choc électrique	46
Fonctionnement normal	47
ATTENTION	47
AVERTISSEMENT	47
Entretien et maintenance corrects	48
AVERTISSEMENT	48
Risque d’explosion	48
Remarque :	48
AVIS :	48
Avertissement issu de la proposition 65 :	48
Causes de pannes	49
AVIS	49
Mise en marche	50
Vue d'ensemble de l'appareil	50
Panneau de commande	51
Composants internes du lave-vaisselle	51
Indicateurs	51
Bouton Information (Bouton Information	51
1. Appuyez sur le bouton ( 8.	51
2. Appuyez sur le bouton de cycle de lavage.	51
3. Pour sortir, appuyez sur le bouton Information ( 8.	51
Première mise sous tension de l'appareil	51
Changez les réglages comme suit :	51
1. Appuyez sur le bouton > ` jusqu'à ce que le réglage désiré soit affiché.	51
2. Effectuez le réglage à l'aide des boutons + - X.	51
3. Appuyez et maintenez le bouton Information enfoncé ( 8 pendant 3 secondes.	51
Réglages	52
Changez les réglages comme suit :	52
1. Ouvrez la porte.	52
2. Appuyez sur le bouton ON/OFF (MARCHE/ARRÊT) (.	52
3. Appuyez sur le bouton Information ( 8 durant 3 secondes jusqu'à ce que le message suivant soit affiché dans la fenêtre d'affichage supérieure @ :	52
4. Appuyez sur le bouton > ` jusqu'à ce que le réglage désiré soit affiché.	52
5. Effectuez le réglage à l'aide des boutons + - X.	52
6. Appuyez et maintenez le bouton Information enfoncé ( 8 pendant 3 secondes.	52
Remarque :	52
Home Connect™	54
Touche InfoTouche Info	54
1. Appuyez sur la touche Info 8.	54
2. Appuyez sur le bouton de cycle de lavage.	54
3. Pour sortir, appuyez sur la touche Info 8.	54
Configurer l’app	54
Configuration de Home Connect	54
1. Ouvrez la porte.	54
2. Appuyez sur le bouton On/Off (Marche/Arrêt) (.	54
3. Appuyez sur la touche Info 8 durant 3 secondes jusqu'à ce que le message suivant soit affiché dans la fenêtre d'affichage supérieure @ :	54
4. Maintenez le bouton > h enfoncé jusqu'à ce que le réglage requis soit affiché dans la fenêtre d'affichage supérieure @.	54
5. Effectuez le réglage à l'aide des boutons + - X.Consultez le tableau dans la section	54
6. Appuyez et maintenez la touche Info enfoncée 8 pendant 3 secondes.	54
Wi-Fi \|	54
Remarques	54
Network login (connexion au réseau)	54
Connexion à l'application	54
Bouton de télédémarrage	55
Remarque :	55
Remarques	55
Wi-Fi sans connexion au serveur Home Connect ƒWi-Fi sans connexion au serveur Home Connect	55
Remarque :	55
Diagnostic à distance ~Diagnostic à distance	55
Remarques	55
Système d'adoucissement de l'eau / sels	56
Tableau de dureté de l'eau	56
Utilisation d'une bandelette pour déterminer la dureté de l’eau	56
Bandelette de test	56
Réglage du système d'adoucissement de l'eau	56
Réglez le système d'adoucissement comme suit :	56
1. Demandez le degré de dureté de votre eau courante à votre fournisseur d'eau.	56
2. Le réglage à effectuer se trouve dans le tableau de dureté de l'eau.	56
3. Ouvrez la porte.	56
4. Appuyez sur le bouton ON/OFF (MARCHE/ARRÊT) (.	56
5. Appuyez sur le bouton Information ( 8 durant 3 secondes jusqu'à ce que le message suivant soit affiché dans la fenêtre d'affichage supérieure @ :	56
6. Maintenez le bouton > ` enfoncé jusqu'à ce que la dureté de l'eau soit affichée dans la fenêtre d'affichage supérieure@.	56
7. Effectuez le réglage à l'aide des boutons + - X.	56
8. Appuyez et maintenez le bouton Information enfoncé ( 8 pendant 3 secondes.	56
Utilisation des sels spéciaux	56
AVIS :	56
Remplissez les sels comme suit :	56
1. Retirez le bouchon à vis du distributeur 1b.	56
2. Remplissez le distributeur d'eau (opération requise uniquement lors de la première mise sous tension de l'appareil).	56
3. Ajoutez les sels tel qu'illustré (n'utilisez pas de sel de table ou de comprimés).	56
Utilisation de détergents chargés en selsDétergent chargé en sels	57
Éteindre l'indicateur de niveau bas de sels/le système d'adoucissement de l'eauÉteindre le système d'adoucissement de l'eau	57
Produit de rinçage	58
Ajout d'agent de rinçage	58
AVIS :	58
1. Ouvrez le distributeur de liquide de rinçage 92 en appuyant sur le loquet du couvercle et en tirant sur celui-ci.	58
2. Remplissez le distributeur 92 de produit de rinçage liquide jusqu'à pleine capacité. Il ne doit pas déborder. Évitez tout déversement dans le trou d'aération.	58
3. Fermez le couvercle. Le couvercle doit être hermétiquement fermé jusqu'à l'encliquetage du loquet, pour garantir son étanchéité.	58
4. Essuyez tout excédent de produit de rinçage déversé lorsque le réservoir est plein.	58
Conseil :	58
AVIS :	58
Réglage de la quantité de produit de rinçage utilisé	58
Réglez la quantité d'agent de rinçage comme suit :	58
1. Ouvrez la porte.	58
2. Appuyez sur le bouton ON/OFF (MARCHE/ARRÊT) (.	58
3. Appuyez sur le bouton Information ( 8 durant 3 secondes jusqu'à ce que le message suivant soit affiché dans la fenêtre d'affichage supérieure @ :	58
4. Maintenez le bouton > ` enfoncé jusqu'à ce que le distributeur d'agent de rinçage soit affiché dans la fenêtre d'affichage supérieure@.	58
5. Effectuez le réglage à l'aide des boutons + - X.	58
6. Appuyez et maintenez le bouton Information enfoncé ( 8 pendant 3 secondes.	58
Remarque :	58
Éteindre l'indicateur d'agent de remplissage de rinçage	59
AVIS :	59
Chargement du lave-vaisselle	60
Matériaux lavables au lave-vaisselle	60
Remarque :	60
Chargement des paniers	60
AVIS :	60
Chargement du panier supérieur	60
Remarque :	60
Chargement du panier inférieur	60
Autres profils de chargement	61
Chargement du panier inférieur	61
Placement recommandé en configuration 12 places	61
Autre configuration	61
Autre profil de chargement avec chaudrons et casseroles	61
Autre configuration avec verres à vin *	61
Chargement du panier supérieur	62
Placement recommandé en configuration 12 places avec tiroir d'ustensiles	62
Placement recommandé en configuration 12 places avec le panier à soirées	62