Thermador DWHD770WFM Instructions for Use - Page 31
Operating the Dishwasher
View all Thermador DWHD770WFM manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 31 highlights
Operating the Dishwasher Note: With hidden controls, the door must be opened before changing settings and closed after changing settings. 9 WARNING RISK OF INJURY To avoid risk of injury, always use caution when opening the door during or following a wash cycle as hot water or steam may escape. Do not fully open the door until water noises have stopped and steam has subsided. Protection against unintentional operation Your dishwasher is equipped with a function that helps to prevent unintentional operation (e.g. by children). After starting the dishwasher, the dishwasher door has to be closed within 4 seconds, otherwise the operation will be paused. There will be a signal on the control panel advising you to press the Start button again and close the door. This function will be activated when: ▯ pressing Start to begin a wash cycle ▯ setting Delay time and pressing Start ▯ opening the door while Delay time is active ▯ opening the door during a wash cycle. Note: This function cannot be deactivated. Operating the touch buttons Buttons are sensitive and should be touched gently. Avoid any grease or food particles resting on the buttons as they could activate the dishwasher. Wiping and cleaning can also activate the dishwasher. For best results, use bare, clean hands when touching the buttons. To clean the touch buttons wipe them with a dry or slightly damp cloth. Changing the settings The dishwasher has been preset with certain settings for your convenience. You can change these factory settings. Change the setting as follows: 1. Open the door. 2. Switch on On/Off button (. 3. Press Info button 8 for 3 seconds until the following text is indicated in the digital display @: Scroll with < > Set with - + Leave with Setup 3 sec. 4. Keep pressing button > ` until the required setting is indicated in the display window at the top @. 5. Make the selection with setting buttons + -X. 6. Press and hold the Info button 8 for 3 seconds. The chosen setting has now been stored. Tip: If you change several settings, first make all changes in succession. Now press the Info button 8 for 3 seconds. This saves all set values in the appliance. AquaSensor The AquaSensor is an optical measuring device which measures the cleanliness of the rinse water. The AquaSensor is used according to the wash cycle. If the AquaSensor is active, "clean" rinse water can be transferred to the next rinse and water consumption can be reduced by 0.8-1-5 gal (3-6 liters). If the rinse water is not yet clear, the water is drained and is replaced with fresh water. In the automatic wash cycles the temperature and running time can also be adjusted to the degree of soiling. Time display The wash cycle time is determined during the wash cycle by the water temperature, the amount of dishes, as well as the degree of soiling and may vary (depending on the selected wash cycle). You can change the time display into time of day or hours/minutes so that the remaining cycle time of the wash cycle appears in the display window "Finish at" (for example 15:20 o'clock) or "Finish in" (for example 3:25 hours). Sensor setting The wash cycle sequence is optimized in Auto wash cycles with the aid of sensors. The sensors adjust the wash cycle strength of Auto wash cycles depending on the amount and type of soiling. You can adjust the sensitivity of the sensors in 3 stages. Standard: This setting is recommend for daily regular or typical use. This is the most energy efficient setting. Sensitive: This setting adjusts the wash cycle strength for the effective removal of food remnants, even if the amount of soiling is low. The energy and water consumption is increased accordingly. Very sensitive: This setting adjusts the wash cycle strength for difficult conditions of use, for example firmly dried on food remnants. This setting is recommended if using biological or eco detergents which contain lower amounts of active agents. The energy and water consumption is increased accordingly. Extra Dry The final rinse uses a higher temperature which improves the drying result. The cycle time may increase slightly. (Caution if utensils are delicate!) You can switch the Extra Dry function on or off. There is a slight increase in energy consumption. Eco forecast When Eco forecast is activated, the average water and energy consumption of the selected wash cycle is briefly displayed in the digital display @. 31