Home » Toshiba Manuals » Flat Panel Televisions » Toshiba 32SL410U » Manual Viewer

Toshiba 32SL410U User Manual - Page 25

Programming channels automatically

Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

Chapter 5: Setting up your TV Programming channels automatically Your TV can automatically detect all active channels in your area and store them in its memory. After the channels are programmed automatically, you can manually add or erase individual channels in the channel memory. Note: • You must configure the ANT/CABLE input source before programming channels ( page 24). • The automatic channel programming process will erase channels that were previously programmed into the TV's memory. • To tune the TV to a channel not programmed in the channel memory, you must use the Channel Number buttons on the remote control. • Programming channels when the ANT/CABLE input is configured for Cable will take substantially longer than when the antenna input is configured for Antenna. This is normal; however, once channel programming is finished, you should not have to repeat the programming process again unless your Cable TV service lineup changes significantly. To program channels automatically: 1 Configure the antenna input source, if you have not already done so ( page 24). 2 Press and open the Setup menu. 3 Highlight Installation and press . up the Start Scan, and press channel programming. Installation Terrestrial Input Configuration Channel Program Channel Options Channel Tuning Mode Time Zone Signal Meter again to begin Auto ANT/CABLE Antenna Scanning channels, please wait... 52% Number of Channels Found - 73 Scanning Digital Channels Found Channels - 118 Cancel The TV will automatically cycle through all the antenna channels, and store all active channels in the channel memory. While the TV is cycling through the channels, the message "Scanning channels, please wait..." appears (as shown above). 5 To cancel channel programming, press on the remote control (or highlight Cancel in the onscreen display and press ). When channel programming is finished, press or to view the programmed channels. Setup Installation REGZA-LINK Setup Sleep Timer PC Settings Media Player 4 (A new set of Installation menu icons will appear, as shown below.) Open the Terrestrial menu, highlight Channel Program and press to bring 25

Section	Page
Chapter 1: Introduction	9
Features of your new TV	9
Overview of steps for installing, setting up, and using your new TV	10
TV front and side panel controls and connections	11
TV back panel connections	12
Chapter 2: Connecting your TV	13
Overview of cable types	13
About the connection illustrations	13
Connecting a VCR and antenna, Cable TV or Camcorder	14
Connecting a DVD player with ColorStream® (component video), a VCR, or a satellite receiver	15
Connecting an HDMI® or DVI device to the HDMI input	16
REGZA-LINK® connection	17
Connecting a digital audio system	18
Connecting a stereo audio system	18
Connecting a personal computer (PC)	19
Chapter 3: Using the remote control	20
Installing the remote control batteries	20
Remote control effective range	20
Adjusting the viewing angle	20
Learning about the remote control	21
Chapter 4: Menu layout and navigation	22
Main menu layout	22
Setup/Installation menu layout	23
Navigating the menu system	23
Chapter 5: Setting up your TV	24
Initial Setup	24
Selecting the menu language	24
Configuring the antenna input source for the ANT/CABLE terminal	24
Programming channels into the TV’s channel memory	24
Programming channels automatically	25
Setting channel skip	26
Labeling channels	26
Setting the HDMI® audio mode	27
Viewing the digital signal meter	28
Setting the time zone	28
Viewing the system status	28
Reset Factory Defaults	28
Chapter 6: Using the TV’s features	29
Selecting the video input source to view	29
Labeling the video input sources	29
To clear the input labels:	30
Tuning channels	30
Tuning channels using the Channel Browser™	30
Favorites Browser	30
To open the Channel Browser™:	31
Elements of the Channel Browser™	31
Adding and clearing channels and inputs in the History List	32
Setting the Channel Tuning Mode	32
Tuning to the next programmed channel	32
Tuning to a specific channel (programmed or unprogrammed)	32
Switching between two channels using Channel Return	33
Switching between two channels using SurfLock™	33
Selecting the picture size	33
Scrolling the TheaterWide® picture (TheaterWide 2 and 3 only)	35
Using the auto aspect ratio feature	35
Selecting the cinema mode	35
Using the FREEZE feature	36
Adjusting the picture	36
Selecting the picture mode	36
Adjusting the picture quality	36
Using the closed caption mode	37
Base closed captions	37
Digital CC Settings	37
CC Selector	37
Adjusting the audio	38
Muting the sound	38
Using the digital audio selector	38
Selecting stereo/SAP broadcasts	38
Adjusting the audio quality	39
Selecting the optical audio output format	39
Using the Dolby® Digital Dynamic Range Control feature	39
Using the Locks menu	39
Entering the PIN code	39
If you cannot remember your PIN code	40
Changing your PIN code	40
Blocking TV programs and movies by rating (V-Chip)	40
Downloading an additional rating system for blocking TV programs and movies	41
Locking channels	42
Unlocking programs temporarily	42
Using the input lock feature	42
Using the Game Timer®	43
Using the control panel lock feature	43
Using the PC settings feature	43
Setting the PC Audio	44
Using the Media Player	44
Using the Media Player with USB	44
To select the Auto Start function	45
To open the Media Player	45
Viewing photo files	45
Playing music files	46
During playback	46
Viewing photo files and playing music files at same time	46
Setting the sleep timer	47
Automatic Power Down	47
No Signal Power Down	48
Using REGZA-LINK®	48
REGZA-LINK® playback device (DVD player, etc.) control	48
REGZA-LINK® input source selection	49
VOLUME and MUTE controls of Audio Receiver	49
Other REGZA-LINK® functions	49
Displaying TV status information	50
Understanding the last mode memory feature	50
Chapter 7: Using the TV’s advanced features	51
Using the advanced picture settings features	51
Using Dynamic Contrast	51
Using the static gamma feature	51
Selecting the color temperature	51
Using CableClear® digital noise reduction	51
Using MPEG noise reduction	52
Using the Color Master® feature	52
Using the Base Color Adjustment	52
Using the Game Mode feature	52
Chapter 8: Troubleshooting	53
General troubleshooting	53
Chapter 9: Appendix	55
Specifications	55
Acceptable signal formats for PC IN and HDMI terminals	56
Limited United States Warranty for LCD Televisions	57

Match case Limit results 1 per page

Chapter 5: Setting up your TV

Programming channels automatically

Your TV can automatically detect all active channels

in your area and store them in its memory. After the

channels are programmed automatically, you can

manually add or erase individual channels in the

channel memory.

Note:

• You must configure the ANT/CABLE input

source before programming channels (

page

24).

• The automatic channel programming process

will erase channels that were previously

programmed into the TV’s memory.

• To tune the TV to a channel not programmed in

the channel memory, you must use the

Channel Number buttons on the remote

control.

• Programming channels when the ANT/CABLE

input is configured for

Cable

will take

substantially longer than when the antenna

input is configured for

Antenna

. This is normal;

however, once channel programming is

finished, you should not have to repeat the

programming process again unless your Cable

TV service lineup changes significantly.

To program channels automatically:

Configure the antenna input source, if you have

not already done so (

page 24).

Press

and open the

Setup

menu.

Highlight

Installation

and press

(A new set of

Installation

menu icons will appear,

as shown below.) Open the

Terrestrial

menu,

highlight

Channel Program

and press

to bring

up the

Start

Scan

, and press

again to begin

channel programming.

The TV will automatically cycle through all the

antenna channels, and store all active channels in

the channel memory. While the TV is cycling

through the channels, the message “Scanning

channels, please wait...” appears (as shown

above).

To cancel channel programming, press

on the

remote control (or highlight

Cancel

in the

onscreen display and press

When channel programming is finished, press

to view the programmed channels.

Setup

Installation

REGZA-LINK Setup

Sleep Timer

PC Settings

Media Player

Terrestrial

Input Configuration

Channel Program

Channel Options

Channel Tuning Mode

Auto

Time Zone

Signal Meter

Installation

ANT/CABLE

Antenna

Scanning channels, please wait...

Number of Channels Found - 73

Scanning Digital Channels

Found Channels - 118

52%

Cancel