Troy-Bilt TB30 Operation Manual - Page 26

Cutting Deck Removal

Get Troy-Bilt TB30 PDF manuals and user guides View all Troy-Bilt TB30 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

Service 7 Cutting Deck Removal To remove the cutting deck, proceed as follows: 5. Remove the remaining bow-tie cotter pins securing the deck to the unit, as shown in Figure 7-3. 1. Place the PTO (Blade Engage) lever in the disengaged (OFF) position and engage the parking brake. 2. Lower the deck by moving the deck lift lever into the bottom notch on the right fender. 3. Remove the bow-tie cotter pin and flat washer from the deck lift assembly, and retain for reinstallation later. See Figure 7-1. Figure 7-1 4. Remove the belt from around the tractor's PTO pulley. See Figure 7-2. Figure 7-3 NOTE: The bow-tie clips should be re-installed from the top down. 6. Unplug the wire pigtail from the deck switch. 7. Move the deck lift lever into the top notch on the right fender to raise the deck lift arms up and out of the way. 8. Carefully remove the PTO cable from the rear of the cutting deck by removing the bow-tie cotter pin which secures it. Remove the spring from the deck idler bracket. See Figure 7-4. Figure 7-2 26 Figure 7-4 9. Gently slide the cutting deck (from the left side) out from underneath the tractor.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
Service
7
26
5.
Remove the remaining bow-tie cotter pins securing the
deck to the unit, as shown in Figure 7-3.
Figure 7-3
NOTE:
The bow-tie clips should be re-installed from the top
down.
6.
Unplug the wire pigtail from the deck switch.
7.
Move the deck lift lever into the top notch on the right
fender to raise the deck lift arms up and out of the way.
8.
Carefully remove the PTO cable from the rear of the cutting
deck by removing the bow-tie cotter pin which secures it.
Remove the spring from the deck idler bracket. See Figure 7-4.
Figure 7-4
9.
Gently slide the cutting deck (from the left side) out from
underneath the tractor.
Cutting Deck Removal
To remove the cutting deck, proceed as follows:
1.
Place the PTO (Blade Engage) lever in the disengaged (OFF)
position and engage the parking brake.
2.
Lower the deck by moving the deck lift lever into the
bottom notch on the right fender.
3.
Remove the bow-tie cotter pin and flat washer from the
deck lift assembly, and retain for reinstallation later.
See
Figure 7-1.
Figure 7-1
4.
Remove the belt from around the tractor’s PTO pulley. See
Figure 7-2.
Figure 7-2