ViewSonic PRO10100 - 1024 x 768 Resolution 6 000 ANSI Lumens 1.26-1.28 Throw Rat - Page 20

Page 20 highlights

Powering On/Off the Projector Powering On the Projector 1. Securely connect the power cord and signal cable. Power on the switch 1 and the Power LED flashes Blue. 2. Turn on the lamp by pressing the " " button either on the control panel of the projector or on the remote control 2. The Power LED will turn blue. The startup screen will display in approximately 10 seconds. The first time you use the projector, you will be asked to select the preferred language and power saving mode. 3. Turn on and connect the source that you want to display on the screen (computer, notebook, video player, etc). The projector will detect the source automatically. If not, push the menu button and go to "OPTIONS". Make sure that "Auto Source" has been set to "Off". `` If you connect multiple sources at the same time, press the direct source buttons on the control panel or on the remote control to switch between inputs. 1 2 Shift Sync Source Turn on the projector first and then select the signal sources. 19 Pattern Power On Standby VGA Video HDMI BNC S-Video DVI Sync Blank Vol + Source Exit Menu Vol - Mute LENS Memory Focus Zoom Shift Lamp PW 1 PIP 4 MyButton 7 RC ID RGB Gain 2 Geo 5 Keystone 8 Reset Mode 3 Blend 6 Aspect 9 0

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
19
Powering On the Projector
1.
Securely connect the power cord and signal cable. Power on the switch
1 and
the Power LED flashes Blue.
2. Turn on the lamp by pressing the
“
”
button either on the control panel of the
projector or on the remote control
2. The Power LED will turn blue.
The startup screen will display in approximately 10 seconds. The first time you
use the projector, you will be asked to select the preferred language and power
saving mode.
3.
Turn on and connect the source that you want to display on the screen
(computer, notebook, video player, etc). The projector will detect the source
automatically. If not, push the menu button and go to “OPTIONS”.
Make sure that “Auto Source” has been set to “Off”.
`
If you connect multiple sources at the same time, press the direct source
buttons on the control panel or on the remote control to switch between
inputs.
Powering On/Off the Projector
1
Source
Sync
Shift
Pattern
VGA
BNC
Sync
Standby
HDMI
DVI
Source
Video
S-Video
Blank
Vol +
Vol -
Exit
Mute
Menu
Memory
Focus
Shift
Zoom
Lamp PW
Mode
RGB Gain
PIP
Blend
Geo
MyButton
Aspect
Keystone
RC ID
Reset
1
2
3
4
5
6
7
8
9
0
LENS
Power On
2
 
Turn on the projector first and then select the signal sources.