ViewSonic PRO10100 - 1024 x 768 Resolution 6 000 ANSI Lumens 1.26-1.28 Throw Rat - Page 21

Page 21 highlights

Powering off the projector 1. Press the "Standby" button on the remote control or the " " button on the control panel to turn off the projector 1. The following message will be displayed on the screen. Press the "Standby" button on the remote control or the " " button on the control panel again 1 to confirm otherwise the message will disappear after 15 seconds. When you press for the second time, the projector will shut down. 2. The cooling fans will complete the cooling cycle for about 60 seconds and the POWER LED will flash Blue. The projector has entered standby mode. If you wish to turn the projector back on, you must wait until the projector has completed the cooling cycle and has entered standby mode. Once in standby mode, simply press the " " button either on the control panel of the projector or on the remote control to restart the projector. 2 3. Power off the switch 3. 4. Disconnect the power cord from the electrical outlet and from the projector. Do not turn on the projector immediately following the power of procedure. Pattern Power On Standby VGA Video HDMI BNC S-Video DVI 3 Sync Blank Source 1 Vol + Shift Sync Source 2 Exit Menu Vol - Mute LENS Memory Focus Zoom Shift Lamp PW 1 PIP 4 MyButton 7 RC ID RGB Gain 2 Geo 5 Keystone 8 Reset Mode 3 Blend 6 Aspect 9 0 20

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
20
Powering Off the Projector
1. Press the “Standby” button on the remote control or the
“
”
button on the con-
trol panel
to turn off the projector
1
. The following message will be displayed on
the screen.
Press the “Standby” button on the remote control or the “
” button on the
control panel again
1
to confirm otherwise the message will disappear after 15
seconds. When you press for the second time, the projector will shut down.
2.
The cooling fans will complete the cooling cycle for about 60 seconds and the
POWER LED will flash Blue. The projector has entered standby mode.
If you wish to turn the projector back on, you must wait until the projector has
completed the cooling cycle and has entered standby mode. Once in standby
mode, simply press the “
” button either on the control panel of the projector
or on the remote control to restart the projector.
2
3. Power off the switch
3
.
4.
Disconnect the power cord from the electrical outlet and from the projector.
3
Source
Sync
Shift
Pattern
VGA
BNC
Sync
Standby
HDMI
DVI
Source
Video
S-Video
Blank
Vol +
Vol -
Exit
Mute
Menu
Memory
Focus
Shift
Zoom
Lamp PW
Mode
RGB Gain
PIP
Blend
Geo
MyButton
Aspect
Keystone
RC ID
Reset
1
2
3
4
5
6
7
8
9
0
LENS
Power On
1
2
 
Do not turn on the projector immediately following the power of procedure.