Weider 150 English Manual - Page 6

Assembly

Get Weider 150 PDF manuals and user guides View all Weider 150 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

ASSEMBLY Before beginning assembly, carefully read the following information and instructions: • Place all parts of the WEIDER® 150 in a cleared area and remove the packing materials; do not dispose of the packing materials until assembly is completed. • Read each assembly step before you begin. • For help identifying the small parts used in assembly, use the PART IDENTIFICATION CHART on the previous page. Note: Some small parts may have been pre-attached for shipping purposes. If a part is not in the parts bag, check to see if it has been pre-attached. • Tighten all parts as you assemble them, unless instructed to do otherwise. • As you assemble the WEIDER• 150, make sure that all parts are oriented as shown in the drawings. THE FOLLOWING TOOLS (NOT INCLUDED) ARE REQUIRED FOR ASSEMBLY: • Two (2) adjustable wrenches • One (1) standard screwdriver • One (1) rubber mallet - • Lubricant, such as grease or petroleum jelly, and soapy water will also be needed. Assembly will be more convenient if you have the following tools: A socket set, a set of open-end or closed-end wrenches, or a set of ratchet wrenches. 1. Before assembling this product, be sure that you have read and understand the information 1 in the box above. Place the Base (40) on the floor. Be sure that the 0 indented holes in the Base are facing the floor. Press a 38mm x 50mm Inner Cap (53) into each side of the Base (40). Insert four M8 x 48mm Carriage Bolts (4) up through the Base (40). 39 0 0 0 Slide an Upright (39) onto one set of M8 x 48mm Carriage Bolts (4) in the Base (40). Hand tighten an M8 Nylon Locknut (1) onto each Carriage Bolt. Do not tighten the Nylon Locknuts yet. Attach the other Upright (39) to the Base (40) in the same manner. 0 0 40 $ a C--53 53 4 4 6 The Indented Holes must face the floor

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
ASSEMBLY
Before
beginning
assembly,
carefully
read
the
following
information
and
instructions:
•
Place
all
parts
of
the
WEIDER®
150
in
a
cleared
area
and
remove
the
packing
materials;
do
not
dispose
of
the
packing
materials
until
assembly
is
completed.
•
Read
each
assembly
step
before
you
begin.
•
For
help
identifying
the
small
parts
used
in
assembly,
use
the
PART
IDENTIFICATION
CHART
on
the
previous
page.
Note:
Some
small
parts
may
have
been
pre
-attached
for
ship-
ping
purposes.
If
a
part
is
not
in
the
parts
bag,
check
to
see
if
it
has
been
pre
-attached.
•
Tighten
all
parts
as
you
assemble
them,
unless
instructed
to
do
otherwise.
•
As
you
assemble
the
WEIDER•
150,
make
sure
that
all
parts
are
oriented
as
shown
in
the
draw-
ings.
THE
FOLLOWING
TOOLS
(NOT
INCLUDED)
ARE
REQUIRED
FOR
ASSEMBLY:
•
Two
(2)
adjustable
wrenches
•
One
(1)
standard
screwdriver
•
One
(1)
rubber
mallet
•
Lubricant,
such
as
grease
or
petroleum
jelly,
and
soapy
water
will
also
be
needed.
—
Assembly
will
be
more
convenient
if
you
have
the
following
tools:
A
socket
set,
a
set
of
open-end
or
closed
-end
wrenches,
or
a
set
of
ratchet
wrenches.
1.
Before
assembling
this
product,
be
sure
that
you
have
read
and
understand
the
information
in
the
box
above.
Place
the
Base
(40)
on
the
floor.
Be
sure
that
the
indented
holes
in
the
Base
are
facing
the
floor.
Press
a
38mm
x
50mm
Inner
Cap
(53)
into
each
side
of
the
Base
(40).
Insert
four
M8
x
48mm
Carriage
Bolts
(4)
up
through
the
Base
(40).
Slide
an
Upright
(39)
onto
one
set
of
M8
x
48mm
Carriage
Bolts
(4)
in
the
Base
(40).
Hand
tighten
an
M8
Nylon
Locknut
(1)
onto
each
Carriage
Bolt.
Do
not
tighten
the
Nylon
Locknuts
yet.
Attach
the
other
Upright
(39)
to
the
Base
(40)
in
the
same
manner.
$
1
0
0
0
a
4
0
39
40
C--53
0
0
4
53
The
Indented
Holes
must
face
the
floor
6