Weider 245 English Manual
Weider 245 Manual
 |
View all Weider 245 manuals
Add to My Manuals
Save this manual to your list of manuals |
Weider 245 manual content summary:
- Weider 245 | English Manual - Page 1
TOLL-FREE CUSTOMER HOT LINE. The trained technicians on our customer hot line will provide immediate assistance, free of charge to you. CUSTOMER HOT LINE: 1-800-999-3756 Mon.-Fri., 6 a.m.-6 p.m. MST CAUTION Read all precautions and instructions in this manual before using this equipment. Save this - Weider 245 | English Manual - Page 2
3 BEFORE YOU BEGIN 4 PART IDENTIFICATION CHART 5 ASSEMBLY 7 ADJUSTMENT 18 WEIGHT RESISTANCE CHART 19 TROUBLE-SHOOTING AND MAINTENANCE 20 CABLE DIAGRAM 21 PART LIST 22 EXPLODED DRAWING 23 ORDERING REPLACEMENT PARTS Back Cover LIMITED WARRANTY Back Cover WEIDER is a registered trademark of - Weider 245 | English Manual - Page 3
at a time, and to support a maximum user weight of 250 pounds. 8. Always stand on the foot plate when performing an exercise that could cause the training system to tip. 9. Always wear athletic shoes for foot protection. 10. Make sure that the cables remain on the pulleys at all times. If the - Weider 245 | English Manual - Page 4
reading further, please review the drawing using the WEIDER® 245 training system. If you have below and familiarize yourself with the parts that are additional questions, please call our Customer Service labeled. Lat Bar Shroud Backrest Press Arm Seat Weight Stack High Pulley Station Butterfly Arm - Weider 245 | English Manual - Page 5
for shipping purposes. If you cannot find a part in the parts bags, check to see if it has been pre-assembled. Note: Assembly is divided into four stages: 1) frame assembly, 2) arm assembly, 3) cable assembly, and 4) seat assembly. The hardware for each stage is packaged separately. Unless otherwise - Weider 245 | English Manual - Page 6
1/4" x 2 1/4" Carriage Bolt (38) 5/16" x 2 1/2" Bolt (22) 3/8" x 2 1/2" Bolt (7) 5/16" x 2 3/4" Shoulder Bolt (85) 1/4" x 3" Bolt (43) 5/16" x 3 1/4" Bolt (14) 3/8" x 3 1/4" Bolt (8) 3/8" x 4" Bolt (16) 3/8" x 4 1/4" Bolt (64) 3/8" x 5" Bolt (75) 5/16" x 6" Bolt (60) 3/8" x 2 1/4" Carriage Bolt (1) - Weider 245 | English Manual - Page 7
that form the skeleton of the training system. Arm Assembly-During this stage you will assemble the arms and the leg lever. Cable Assembly-During this stage you will attach the cables and pulleys. Seat Assembly-During the final stage you will assemble the seat, backrest, and miscellaneous parts. 7 - Weider 245 | English Manual - Page 8
FRAME ASSEMBLY 1. Press a 1 1/2" x 2 1/2" Outer Cap (73) onto each end of the Stabilizer (5). Press a 1 3 4 42 21 4. Slide a Weight Bumper (19) down over each Weight Guide (62). Slide the Weights (25) onto the Weight Guides (62). Make sure all of the Weights are oriented exactly as shown, with the - Weider 245 | English Manual - Page 9
Tube Cap (72) into the indicated end of the Weight Tube (63). Slide the Weight Tube into the center holes in the Weights (25). Slide the Top Weight (56) down onto the Weight Guides (62) as shown. 5 62 56 63 72 25 FRAME ASSEMBLY 6. Press four 1 1/2" x 2 1/2" Inner Caps (27) into the Top Frame - Weider 245 | English Manual - Page 10
FRAME ASSEMBLY 8. Attach the Top Frame (55) to the Weight Guides (62) using a 5/16" x 6" Bolt (60), two 1/2" x 1/2" Spacers (61), and a 5/16" Nylon Locknut (3) as shown. Tighten all Nylon Locknuts used in Press Arm (46) in the same manner. 46 17 16 Lubricate 4 21 44 49 46 3 22 17 ARM ASSEMBLY 10 - Weider 245 | English Manual - Page 11
Nylon Locknut (2). 38 36 37 12. Attach a Bumper (11) to the Seat Frame (36) 12 using a #10 x 1" Screw (80). 78 2 36 11 80 ARM ASSEMBLY 13. Attach the Seat Frame (36) to the Front 13 Upright (42) using two 3/8" x 3 1/4" Bolts (8), a Back Plate (71), and two 3/8" Nylon Locknuts (21 - Weider 245 | English Manual - Page 12
the inset drawing. Attach the Left Arm (47) in the same manner. 17. Important: As you assemble the cables in steps 17-30, refer to the CABLE DIAGRAM on page 21 for correct cable routing. Route the Short Cable (23) up through the hole in the Top Frame (55) as shown. Make sure the ball is - Weider 245 | English Manual - Page 13
CABLE ASSEMBLY 19. Route the Short Cable (23) around two "V"- 19 Pulleys (6). Attach the Pulleys and two Long Cable Traps (50) the end of the Short Cable (23) to the "U" Bracket (57) with a 1/4" Washer (78) and a 1/4" Nylon Locknut (2). Attach the "U" Bracket (57) to the Weight Tube (63) using a - Weider 245 | English Manual - Page 14
assembled 3 1/2" Pulleys (15) from the Pulley Plates (58). Route the Short Cable (23) around one of the Pulleys. Reattach a Pulley Plate to each side of the Pulley Route the Long Cable (69) around the other 3 1/2" Pulley (15). Attach the Pulley to the bottom set of holes in the Pulley Plates (58) - Weider 245 | English Manual - Page 15
CABLE ASSEMBLY 27. Route the Long Cable (69) behind the Press Frame (17) and under the Seat Frame (36) as shown. Route the Long Cable around two 3 1/2" Pulleys (15). Slide the 3/8" x 5" Bolt (75) through the 3 1/2" Pulleys (15), two Cable Traps (66), and the Press Frame (17) as shown. Tighten a - Weider 245 | English Manual - Page 16
78 41 SEAT ASSEMBLY 33. Insert the training system, remove the 1 1/2" Square Inner Cap (32) from the Seat Frame (36). Insert the Curl Post into the Seat Frame and tighten the Knob (51) into the Seat Frame and the Curl 32 18 Post. 35 Note: When the Curl Post (35) is not in 51 use, replace - Weider 245 | English Manual - Page 17
training system, pull each cable a few times to be sure that the cables move smoothly over the pulleys. If one of the cables does not move smoothly, find and correct the problem. IMPORTANT: If the cables are not properly installed, they may be damaged when heavy weight is used. See the CABLE DIAGRAM - Weider 245 | English Manual - Page 18
ADJUSTMENT The instructions below describe how each part of the training system can be adjusted. Refer to the exercise guide accompanying this manual to see how the training system should be used for each exercise. IMPORTANT: When attaching the lat bar or nylon strap, make sure that the accessories - Weider 245 | English Manual - Page 19
resistance for each butterfly arm.The actual resistance at each weight station may vary due to differences in individual weight plates, as well as friction between the cables, pulleys, and weight guides. WEIGHT PLATES High Pulley (lbs.) Arm Press (lbs.) Butterfly (lbs.) Leg Raise (lbs.) Low - Weider 245 | English Manual - Page 20
TROUBLE-SHOOTING AND MAINTENANCE Make sure all parts are properly tightened each time you use the training system. Replace any worn parts immediately. The training system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents. TIGHTENING THE CABLES Woven cable, the - Weider 245 | English Manual - Page 21
the diagram to be sure that the cables and the cable traps have been assembled correctly. If the cables have not been cor- rectly routed, the training system will not function properly and damage may occur. The cable traps should be positioned so that the cables will not come off the pulleys. Be - Weider 245 | English Manual - Page 22
Spacer Lat Bar Holder Sleeve 1 1/4" x 2 1/2" Plastic Bushing 5/16" x 2 3/4" Shoulder Bolt 5/16" x 1 3/4" Bolt 5/16" Nylon Jamnut 5/16" SAE Washer User's Manual Exercise Guide Exercise Chart Decal Note: "#" indicates a non-illustrated part. Specifications are subject to change without notice. 22 - Weider 245 | English Manual - Page 23
EXPLODED DRAWING-Model No. WESY19002 R0303A 79 60 3 61 62 79 23 57 78 86 32 56 63 74 79 27 40 71 7 40 9 76 50 21 6 55 10 89 - Weider 245 | English Manual - Page 24
to give the following information: • The MODEL NUMBER of the product (WESY19002) • The NAME of the product (WEIDER® 245 training system) • The SERIAL NUMBER of the product (see the front cover of this manual) • The KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST and the EXPLODED
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
 |
 |
USER'S MANUAL
QUESTIONS?
As a manufacturer, we are
committed to providing complete
customer satisfaction. If you
have questions, or if there are
missing parts, we will guarantee
complete satisfaction through
direct assistance from our factory.
TO AVOID UNNECESSARY
DELAYS, PLEASE CALL DIRECT
TO OUR TOLL-FREE CUSTOMER
HOT LINE. The trained techni-
cians on our customer hot line
will provide immediate assis-
tance, free of charge to you.
CUSTOMER HOT LINE:
1-800-999-3756
Mon.–Fri., 6 a.m.–6 p.m. MST
Model No. WESY19002
Serial No.
Write the serial number in the
space above for reference.
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
Serial Number Decal (under seat)
Visit our website at
www.weiderfitness.com
new products, prizes,
fitness tips, and much more!
®