Xerox M118i System Administration Guide - Page 98

NetWare, Auto Master Mode

Get Xerox M118i - WorkCentre B/W Laser PDF manuals and user guides
UPC - 095205219265
View all Xerox M118i manuals
Add to My Manuals
Save this manual to your list of manuals

Page 98 highlights

11 CentreWare Internet Services 1. At the CentreWare Internet Services home page for the machine, select the [Properties] tab. 2. In the [Properties] frame, select the plus symbol [+] to the left of the [Protocol Settings] folder. 3. Select [SMB]. 4. Set up the following options to be displayed in the frame. • Workgroup • Host Name • Administrator Name • Administrator Password • Re-enter Password • Maximum Sessions • TBCP Filter (Only available when the optional PostScript Kit is installed.) • Unicode Support • Auto Master Mode • Encrypt Password NOTE: For more information about the options, refer to Properties in the CentreWare Internet Services chapter of the User Guide. 5. Select [Apply New Settings] to reflect the new setting. 6. Enter the user ID and password, then select [OK]. NOTE: The default user ID is "admin" and the default password is "x-admin". 7. When the reboot message appears, select [Reboot]. NetWare This page allows you to configure the NetWare settings for the following options. NOTE: Some settings on this page will only be available after you reboot the machine from CentreWare Internet Services, or after the machine is switched off and on. 1. At the CentreWare Internet Services home page for the machine, select the [Properties] tab. 2. In the [Properties] frame, select the plus symbol [+] to the left of the [Protocol Settings] folder. 3. Select [NetWare]. 4. Set up the following options to be displayed in the frame. • Host Name • Active Mode 98 Xerox CopyCentre/WorkCentre 118 System Administration Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
11
CentreWare Internet Services
98
Xerox CopyCentre/WorkCentre 118 System Administration Guide
1.
At the CentreWare Internet Services home page for the machine, select the
[Properties] tab.
2.
In the [Properties] frame, select the plus symbol [+] to the left of the [Protocol
Settings] folder.
3.
Select [SMB].
4.
Set up the following options to be displayed in the frame.
•
Workgroup
•
Host Name
•
Administrator Name
•
Administrator Password
•
Re-enter Password
•
Maximum Sessions
•
TBCP Filter (Only available when the optional PostScript Kit is installed.)
•
Unicode Support
•
Auto Master Mode
•
Encrypt Password
NOTE:
For more information about the options, refer to Properties in the CentreWare
Internet Services chapter of the User Guide.
5.
Select [Apply New Settings] to reflect the new setting.
6.
Enter the user ID and password, then select [OK].
NOTE:
The default user ID is "admin" and the default password is "x-admin".
7.
When the reboot message appears, select [Reboot].
NetWare
This page allows you to configure the NetWare settings for the following options.
NOTE:
Some settings on this page will only be available after you reboot the machine
from CentreWare Internet Services, or after the machine is switched off and on.
1.
At the CentreWare Internet Services home page for the machine, select the
[Properties] tab.
2.
In the [Properties] frame, select the plus symbol [+] to the left of the [Protocol
Settings] folder.
3.
Select [NetWare].
4.
Set up the following options to be displayed in the frame.
•
Host Name
•
Active Mode