Xerox P8EX DocuColor 8000/7000 System Adminstration Guide - Page 63

Using the Deculer Setup, Decurler Setup

Get Xerox P8EX - DocuPrint B/W Laser Printer PDF manuals and user guides
UPC - 095205085853
View all Xerox P8EX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 63 highlights

1 . Too l s M od e If paper curl is a problem, using one of these preset parameters usually eliminates the problem. However, due to the broad range of paper variables, image coverage, and environmental factors, these defaults settings may not result in satisfactory performance. If paper curl is interfering with digital press performance, begin by adjusting the decurler settings by selecting an alternate Decurler Paper Type A through Type D. If the problem continues, additional decurler settings are available and identified as Decurler Paper Types E1 through E6. NOTE: Before using the E1-E6 Decurler Types, you must set up the desired E Type setting by following the instructions in Decurler E Table Settings procedure provided later in this chapter. Using the Deculer Setup 1. Load the Paper Tray with the paper you wish to use for a job. Make the correct paper weight selections on the tray for the paper being used and run a few test prints. If there is too much curl, continue with step 2. 2. On the Machine Defaults 2 screen, touch the Decurler Setup button. The Decurler Setup screen opens. DocuColor 8000/7000 System Administration Guide 1-39

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
DocuColor 8000/7000 System Administration Guide
1-39
1. Tools Mode
If paper curl is a problem, using one of these preset parameters
usually eliminates the problem.
However, due to the broad range
of paper variables, image coverage, and environmental factors,
these defaults settings may not result in satisfactory performance.
If paper curl is interfering with digital press performance, begin by
adjusting the decurler settings by selecting an alternate Decurler
Paper Type A through Type D.
If the problem continues,
additional decurler settings are available and identified as
Decurler Paper Types E1 through E6.
NOTE:
Before using the E1-E6 Decurler Types, you must set up
the desired E Type setting by following the instructions in Decurler
E Table Settings procedure provided later in this chapter.
Using the Deculer Setup
1.
Load the Paper Tray with the paper you wish to use for a
job.
Make the correct paper weight selections on the tray for
the paper being used and run a few test prints.
If there is too
much curl, continue with step 2.
2.
On the
Machine Defaults 2
screen, touch the
Decurler Setup
button. The
Decurler Setup
screen opens.