Yamaha EMX66M Owner's Manual - Page 23
As a band PA, Connections
View all Yamaha EMX66M manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 23 highlights
Example setups 21 As a band PA Here is an example of using the EMX66M as a small PA for a band. In this example, the monitor speakers are being sent a mix that is independent of the MAIN speaker mix. An external effect such as delay or reverb is also being used. Connections • Connect mics or instruments, such as keyboards, to the channel input jacks 1-6. • Connect the main speakers to the SPEAKERS A 1/2 jacks, and connect the monitor speakers to the SPEAKERS B 1/2 jacks. Then, set the power amp select switch to "MAIN-MON." • If you will be using an external effect such as delay or reverb, connect the EMX66M's EFFECT OUT jack to the input jack of the external effect, and connect the output jack of the external effect to the EMX66M's AUX IN jack. Note: Set the power amp select switch of the POWER AMP section to the "MAIN MON" position. If you are using an external effect, we recommend that you turn down the EFFECT RTN controls of the MAIN and MONITOR sections. If the external effect has a stereo output, it is possible to connect its output jacks to the LINE jacks of channels 5. However in this case, be sure that the EFFECT controls are turned all the way down for the channels into which the effect sound is being input. If the EFFECT controls are raised, feedback will occur, and your speakers may be damaged. Main Speakers Monitors Speakers SPEAKERS A SPEAKERS B 1 HIGH 2 HIGH 3 HIGH 4 HIGH 5 HIGH 6 HIGH -15 +15 MID -15 +15 MID -15 +15 MID -15 +15 MID -15 +15 MID -15 +15 MID -15 +15 LOW -15 +15 LOW -15 +15 LOW -15 +15 LOW -15 +15 LOW -15 +15 LOW -15 +15 MONITOR -15 +15 MONITOR -15 +15 MONITOR -15 +15 MONITOR -15 +15 MONITOR -15 +15 MONITOR 0 +15 EFFECT 0 +15 EFFECT 0 +15 EFFECT 0 +15 EFFECT 0 +15 EFFECT 0 +15 EFFECT 0 +15 LEVEL 0 +15 LEVEL 0 +15 LEVEL 0 +15 LEVEL 0 +15 LEVEL 0 +15 LEVEL DIGITAL EFFECT VOCAL ECHO 1 VOCAL ECHO 2 VOCAL REVERB 1 VOCAL REVERB 2 HALL 1 HALL 2 ROOM PLATE ON +12 +12 +6 6 6 +3 0 0 0 6 6 -5 -12 -12 -10 125 250 500 1k 2k 4k 8k GEQ 0 10 EFFECT RTN 0 10 2TR IN MONITOR 0 10 MASTER +12 +12 +6 6 6 +3 0 0 0 6 6 -5 -12 -12 -10 125 250 500 1k 2k 4k 8k GEQ PHANTOM ON OFF POWER AMP LIMITER MAIN MAIN MON MAIN MAIN BRIDGE A B YAMAHA SPEAKER PROCESSING 0 10 PAD 1 0 10 PAD 2 0 10 PAD 3 0 10 PAD 4 0 10 PAD 5 0 10 PAD 6 EFFECT 0 10 EFFECT RTN 0 10 AUX IN MAIN 0 10 2TR IN 0 10 MASTER power Hi-Z Low-Z Hi-Z Low-Z Hi-Z Low-Z Hi-Z Low-Z LINE 1 2 MIC Super Hi-Z 1 2 MIC EFFECT OUT FOOT SW INPUT TO MAIN OUT PUT 2TR REC IN OUT 1 1 AUX IN 2 2 MAIN EEEngine MONITOR ON / OFF SEE REAR PANEL CAUTION Power amp select switch MAIN MAIN MON MAIN MAIN BRIDGE Microphone Keyboard 88 Effects Processor Electric bass Footswitch (YAMAHA FC5) *1. Although this example shows an ex- ternal effects processor and foot- Electric-acoustic guitar switch, which is used to turn on and off the built-in digital effects processor, connected to the EMX66M, in practice, only one effects processor, internal or external, will be used at a time, so the footswitch is not required when using external effects. EMX66M-Owner's Manual