ZyXEL EOC350 Series User Guide - Page 23

Chapter 5 EP Management

EOC350 Series User’s Guide

23

The following table describes the items in this screen.

5.3

The View Host Screen

Use this screen to view which hosts are connected to termination adapters. Click

EP Management

>

View Host

to show the following screen.

Table 9

EP Management

LABEL

DESCRIPTION

Master

This shows the version of the termination system’s EoC driver in the upload area of the

termination system.

EP

This shows the version of the termination adapter’s EoC driver in the upload area of the

termination system.

On-line EP

This shows the number of termination adapters that are online.

Off-line EP

This shows the number of termination adapters that are offline.

Refresh

Click this to refresh this screen.

View Host

Click this to show which hosts are connected to termination adapters.

Igmp Group

Click this to view IGMP groups and their host members.

No

This shows the index of the row.

Sel

This shows which termination adapters are selected for manual upgrade or reconfiguration.

Click

Sel

to select all termination adapters.

Link

This shows which the current link status of each device.

•

Green:

The device is online. The termination system device is always online unless its

EoC driver is broken.

•

Yellow:

The termination adapter is being initialized by the termination system.

•

Red:

The termination adapter is active but can’t be configured by termination system.

•

Gray:

The termination adapter is offline.

PE (Up/Dn)

This shows the Payload Encoding (PE) in Mbps for the upstream and downstream directions

between each termination adapter and the termination system. Click this to refresh the

column.

MAC

This shows the MAC address used over Coax.

Model

This shows the current queried model number.

EoC Driver

This shows the current queried working (running) EoC driver version.

Note

This shows a user definable note for the device.

Ether

Click

Config

to configure EoC and Ethernet properties of a device. These properties are

stored in the termination system’s nonvolatile memory and downloaded to termination

adapters when they power up.

Test

Click

Test

to run the built-in diagnostic functions.

Mtn

Click

Backup

or

Restore

to download or upload a termination adapter’s configuration file.

Upgrade EoC

Driver

Click this to upgrade the EoC drivers of the selected termination adapters with new driver in

the termination system’s upload area.

ReConfig

Click this to reload the EoC configuration of the selected termination adapters from the

termination system.

Add EP

Click this to add an offline termination adapter profile. This is useful for provisioning

termination adapters before they go online.

Del EP

Click this to add an offline termination adapter profile. This saves memory on the

termination system.

Section	Page
EOC350 Series	1
Contents Overview	3
Table of Contents	4
Introduction	9
1.1 Overview	9
1.1.1 Integrating the EOC350-TS and EOC350-TA with Satellite TV	9
1.1.2 Integrating the EOC350-TS and EOC350-TA with an STB	10
1.2 EOC350-TS	10
1.2.1 LEDs	11
1.2.2 Connections	11
1.3 EOC350-TA	12
1.3.1 LEDs	12
1.3.2 Connections	13
1.4 The RESET Button	13
1.5 Ways to Manage the EOC350-TS	14
The Web Configurator	15
2.1 Overview	15
2.1.1 Accessing the Web Configurator	15
2.2 Securing the EOC350-TS	16
2.3 The Web Configurator Layout	17
2.3.1 Navigation Panel	17
2.3.2 Main Window	18
System Setup	19
3.1 Overview	19
3.2 The System Setup Screen	19
Auto Configuration	21
4.1 Overview	21
4.2 The Auto Configuration Screen	21
EP Management	22
5.1 Overview	22
5.2 The EP Management Screen	22
5.3 The View Host Screen	23
5.4 The View Host Screen	24
5.5 Termination System Configuration	25
5.5.1 The EoC Screen (Privacy Mode)	25
5.5.2 The Port Screen	25
5.5.3 The QoS Screen	26
5.5.4 The IGMP Screen	27
5.5.5 The VLAN Screen	28
5.5.6 The Status Screen	29
5.6 Testing from the Termination System	29
5.7 Ether EP Default Profile Configuration	30
5.7.1 The EoC Screen	30
5.7.2 The Port Screen	31
5.7.3 The QoS Screen	32
5.7.4 The IGMP Screen	33
5.7.5 The VLAN Screen	33
5.7.6 The Filter Screen	34
5.8 EP Configuration	35
5.8.1 The EoC Screen	35
5.8.2 The Port Screen	35
5.8.3 The QoS Screen	37
5.8.4 The IGMP Screen	37
5.8.5 The VLAN Screen	38
5.8.6 The Filter Screen	39
5.8.7 The Status Screen	39
5.9 Testing from a Termination Adapter	40
5.9.1 Noise	40
5.9.2 Online Diag	41
5.10 Backup and Restore of Termination Adapter Configuration	42
5.10.1 Backup Configuration	42
5.10.2 Restore Configuration	43
5.11 Adding Offline Termination Adapters	43
Administration	45
6.1 Overview	45
6.2 The Administrator Screen	45
6.3 The Allowed Source Screen	46
6.4 The Telnet Setup Screen	47
6.5 The HTTP Setup Screen	48
6.6 The SNMP Setup Screen	49
6.7 The SNMP Trap Server Screen	49
System Log	51
7.1 Overview	51
7.2 The Syslog Setup Screen	51
7.3 The Syslog View Screen	52
System Time	53
8.1 Overview	53
8.2 The SNTP Setup Screen	53
8.3 The View Time Screen	54
Static MAC	55
9.1 Overview	55
9.2 The Static MAC Screen	55
Maintenance	56
10.1 Overview	56
10.2 Rebooting the System	56
10.3 Restoring Default Settings	56
10.4 Uploading Firmware	56
10.5 The Activate Firmware Screen	58
10.6 Backup and Restore	59
10.6.1 Backup Configuration	59
10.6.2 Restore Configuration	60
Telnet	61
11.1 Overview	61
11.2 Config Telnet Server	61
11.2.1 Command Format	61
11.2.2 Generic Command Sets	62
SNMP	71
12.1 Overview	71
Troubleshooting	73
13.1 Power, Hardware Connections, and LEDs	73
13.2 EOC350-TS Access and Login	74
13.3 Bandwidth and Connectivity	75
13.4 Resetting the EOC350-TS to Factory Defaults	76

ZyXEL EOC350 Series User Guide - Page 23

The View Host Screen

Page 23 highlights