ZyXEL EOC350 Series User Guide - Page 36

Chapter 5 EP Management

EOC350 Series User’s Guide

36

Figure 28

EP Management > Ether > Config > Port (termination adapter)

The following table describes the items in this screen.

Table 25

EP Management > Ether > Config > Port (termination adapter)

LABEL

DESCRIPTION

Port

This shows the port name for this row.

Service

Select

On

to enable this port or

Off

to disable it.

Speed/Duplex

Select the speed and the duplex mode of the Ethernet connection on this port. Choices are

Auto

,

10M/Full

,

10M/Half

,

100M/Full

,

100M/Half

. Selecting

Auto

(auto-negotiation)

allows the port to negotiate with a peer port automatically to obtain the connection speed

and duplex mode that both ends support. If the peer port does not support auto negotiation

or turns off this feature, the EOC350-TA determines the connection speed by detecting the

signal on the cable and using half duplex mode.

Flow Ctrl

A concentration of traffic on a port decreases port bandwidth and overflows buffer memory

causing frame losses. Select

On

to enable flow control and regulate transmission of frames

to match the bandwidth of the receiving port.

Enable UpRate

Limit

Select

Enable

to throttle the upstream bandwidth through this port.

UpRate

(*64Kbps)

Type a bandwidth value in 64Kbps increments. If this exceeds

1536

(100Mbps) on a

termination adapter LAN port or 3125 (200Mbps) on an FoC port, there will be no bandwidth

throttling.

Enable

DownRate

Limit

Select

Enable

to throttle the downstream bandwidth through this port.

DownRate

(*64Kbps)

Type a bandwidth value in 64Kbps increments. If this exceeds

1536

(100Mbps) on a

termination adapter LAN port or 3125 (200Mbps) on an FoC port, there will be no bandwidth

throttling.

Apply

Click

Apply

to save your settings.

Back

Click

Back

to return to the main EP Management screen.

Section	Page
EOC350 Series	1
Contents Overview	3
Table of Contents	4
Introduction	9
1.1 Overview	9
1.1.1 Integrating the EOC350-TS and EOC350-TA with Satellite TV	9
1.1.2 Integrating the EOC350-TS and EOC350-TA with an STB	10
1.2 EOC350-TS	10
1.2.1 LEDs	11
1.2.2 Connections	11
1.3 EOC350-TA	12
1.3.1 LEDs	12
1.3.2 Connections	13
1.4 The RESET Button	13
1.5 Ways to Manage the EOC350-TS	14
The Web Configurator	15
2.1 Overview	15
2.1.1 Accessing the Web Configurator	15
2.2 Securing the EOC350-TS	16
2.3 The Web Configurator Layout	17
2.3.1 Navigation Panel	17
2.3.2 Main Window	18
System Setup	19
3.1 Overview	19
3.2 The System Setup Screen	19
Auto Configuration	21
4.1 Overview	21
4.2 The Auto Configuration Screen	21
EP Management	22
5.1 Overview	22
5.2 The EP Management Screen	22
5.3 The View Host Screen	23
5.4 The View Host Screen	24
5.5 Termination System Configuration	25
5.5.1 The EoC Screen (Privacy Mode)	25
5.5.2 The Port Screen	25
5.5.3 The QoS Screen	26
5.5.4 The IGMP Screen	27
5.5.5 The VLAN Screen	28
5.5.6 The Status Screen	29
5.6 Testing from the Termination System	29
5.7 Ether EP Default Profile Configuration	30
5.7.1 The EoC Screen	30
5.7.2 The Port Screen	31
5.7.3 The QoS Screen	32
5.7.4 The IGMP Screen	33
5.7.5 The VLAN Screen	33
5.7.6 The Filter Screen	34
5.8 EP Configuration	35
5.8.1 The EoC Screen	35
5.8.2 The Port Screen	35
5.8.3 The QoS Screen	37
5.8.4 The IGMP Screen	37
5.8.5 The VLAN Screen	38
5.8.6 The Filter Screen	39
5.8.7 The Status Screen	39
5.9 Testing from a Termination Adapter	40
5.9.1 Noise	40
5.9.2 Online Diag	41
5.10 Backup and Restore of Termination Adapter Configuration	42
5.10.1 Backup Configuration	42
5.10.2 Restore Configuration	43
5.11 Adding Offline Termination Adapters	43
Administration	45
6.1 Overview	45
6.2 The Administrator Screen	45
6.3 The Allowed Source Screen	46
6.4 The Telnet Setup Screen	47
6.5 The HTTP Setup Screen	48
6.6 The SNMP Setup Screen	49
6.7 The SNMP Trap Server Screen	49
System Log	51
7.1 Overview	51
7.2 The Syslog Setup Screen	51
7.3 The Syslog View Screen	52
System Time	53
8.1 Overview	53
8.2 The SNTP Setup Screen	53
8.3 The View Time Screen	54
Static MAC	55
9.1 Overview	55
9.2 The Static MAC Screen	55
Maintenance	56
10.1 Overview	56
10.2 Rebooting the System	56
10.3 Restoring Default Settings	56
10.4 Uploading Firmware	56
10.5 The Activate Firmware Screen	58
10.6 Backup and Restore	59
10.6.1 Backup Configuration	59
10.6.2 Restore Configuration	60
Telnet	61
11.1 Overview	61
11.2 Config Telnet Server	61
11.2.1 Command Format	61
11.2.2 Generic Command Sets	62
SNMP	71
12.1 Overview	71
Troubleshooting	73
13.1 Power, Hardware Connections, and LEDs	73
13.2 EOC350-TS Access and Login	74
13.3 Bandwidth and Connectivity	75
13.4 Resetting the EOC350-TS to Factory Defaults	76

ZyXEL EOC350 Series User Guide - Page 36

Table 25, Label, Description

Page 36 highlights