ZyXEL EOC350 Series User Guide - Page 63

Description

Get ZyXEL EOC350 Series PDF manuals and user guides View all ZyXEL EOC350 Series manuals
Add to My Manuals
Save this manual to your list of manuals

Page 63 highlights

Chapter 11 Telnet Table 50 Generic Telnet Commands (continued) COMMANDS ARGUMENTS [ ] IS OPTIONAL DESCRIPTION dir Show details of files in the flash ROM, including the working area and upload area. The listed filenames are: dns [-s ] • bootcode: boot loader • sysfw4m: system firmware • G2C44H2xM: ertmination system EoC driver • G2C44H2xEp: EP(3210) EoC driver • G3C1244xEp: EP(3310) EoC driver • diagsw: diagnosis utility file Details shown include the file id, file version, file date, and file size. Display or setup DNS server settings. exit quit ep [-c ] • -s pri : setup Primary DNS server's IP • -s sec : setup Secondary DNS server's IP Close the Telnet console. Close the Telnet console. Setup termination adapter EoC properties. ephpnareboot epreg eprestore epstat epswc [-n ] -m -m -m -m -m [-r] -m [-t] [-u] [-r] [-d] [-p [-l ] [-s ] [-f ]] • : termination adapter Host Limit (0~12), default 3 • : termination adapter Note • : The EoC MAC address of the termination adapter being configured. Reset termination adapter EoC device Add a termination adapter profile, (like Add EP in the Web Configurator) Apply termination adapter EoC/Ethernet properties (settings in termination system) to a termination adapter, (like ReConfig EP in the Web Configurator). Display termination adapter LAN1/LAN2/EoC port statistics. • -r: reset all port statistics counters to 0. Display or setup the Ethernet properties of a termination adapter's built-in switch. • -t: display termination adapter switch settings • -u: display termination adapter switch/port status • -r: reset termination adapter switch • -d: reset termination adapter switch settings to factory defaults • -p: configure termination adapter LAN1/LAN2/ EoC port • -l: link, : force current port to link up or down, i.e. enable/disable current port • -s: current port Ethernet mode setting, : auto-negotiation mode : 10/100Mbps, half/fullduplex mode • -f: current port Ethernet flow-control setting, : turn on /off flow control EOC350 Series User's Guide 63

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
Chapter 11 Telnet
EOC350 Series User’s Guide
63
dir
Show details of files in the flash ROM, including the
working area and upload area. The listed
filenames are:
•
bootcode: boot loader
•
sysfw4m: system firmware
•
G2C44H2xM:
t
ermination system EoC driver
•
G2C44H2xEp: EP(3210) EoC driver
•
G3C1244xEp: EP(3310) EoC driver
•
diagsw: diagnosis utility file
Details shown include the file id, file version, file
date, and file size.
dns
[-s <pri/sec> <ip>]
Display or setup DNS server settings.
•
-s pri <ip>: setup Primary DNS server's IP
•
-s sec <ip>: setup Secondary DNS server's IP
exit
Close the Telnet console.
quit
Close the Telnet console.
ep
[-c <hostcnt>]
[-n <note>]
-m <mac>
Setup termination adapter EoC properties.
•
<hostcnt>: termination adapter Host Limit
(0~12), default 3
•
<note>: termination adapter Note
•
<mac>: The EoC MAC address of the
termination adapter being configured.
ephpnareboot
-m <mac>
Reset termination adapter EoC device
epreg
-m <mac>
Add a termination adapter profile, (like Add EP in
the Web Configurator)
eprestore
-m <mac>
Apply termination adapter EoC/Ethernet properties
(settings in termination system) to a termination
adapter, (like ReConfig EP in the Web
Configurator).
epstat
-m <mac>
[-r]
Display termination adapter LAN1/LAN2/EoC port
statistics.
•
-r: reset all port statistics counters to 0.
epswc
-m <mac>
[-t]
[-u]
[-r]
[-d]
[-p <lan1/lan2/hpna> [-l <up/
down>] [-s <auto /10h /10f /100h /
100f>] [-f <on/off>]]
Display or setup the Ethernet properties of a
termination adapter’s built-in switch.
•
-t: display termination adapter switch settings
•
-u: display termination adapter switch/port
status
•
-r: reset termination adapter switch
•
-d: reset termination adapter switch settings to
factory defaults
•
-p: configure termination adapter LAN1/LAN2/
EoC port
•
-l: link, <up/down>: force current port to link
up or down, i.e. enable/disable current port
•
-s: current port Ethernet mode setting,
<auto>: auto-negotiation mode
<10h/10f/100h/100f>: 10/100Mbps, half/full-
duplex mode
•
-f: current port Ethernet flow-control setting,
<on/off>: turn on /off flow control
Table 50
Generic Telnet Commands (continued)
COMMANDS
ARGUMENTS
[ ] IS OPTIONAL
DESCRIPTION