Alpine CDA-117 Owner's Manual (english) - Page 40

Setting the Time Correction Unit (TCR Parameter) You can change the unit, (cm or inch) of time correction.  Setting item: TCR Parameter Setting contents: cm (Initial setting) / inch Sound Field Adjustment The setting of Parametric EQ/Graphic EQ, Time Correction and X-Over can be adjusted in this mode. Adjusting the Parametric Equalizer Curve You can modify the Equalizer settings to create a response curve more appealing to your personal taste. To adjust the Parametric Equalizer Curve, set the EQ Mode to Parametric EQ. For details, refer to "Setting EQ mode" on page 37. 1 After selecting Parametric EQ from the Sound Field Adjustment mode, press BAND to select the band to be adjusted. Band 1  Band 2  Band 3  Band 4  Band 5  Band 1 2 Press  or  to select frequency bands. Adjustable frequency bands: 20 Hz to 20 kHz (in 1/3 octave steps). Band-1 Band-2 Band-3 Band-4 Band-5 20 Hz~80 Hz (63 Hz) 50 Hz~200 Hz ( 150 Hz) 125 Hz~3.2 kHz (400 Hz) 315 Hz~8 kHz (1 kHz) 800 Hz~20 kHz (2.5 kHz) 3 Turn the Rotary encoder to adjust the level. Adjustable level: −6 to +6 dB 4 Press SOURCE to set the bandwidth (Q). Adjustable bandwidth: 1, 1.5, 3 5 To adjust another band, repeat steps 1 to 4 and adjust all bands. Notes • The frequencies of adjacent bands cannot be adjusted within 4 steps. • While adjusting the Parametric EQ, you should consider the frequency response of the connected speakers. Adjusting the Graphic Equalizer Curve You can modify the equalizer settings to create a response curve more appealing to your personal taste. To adjust the graphic equalizer curve, set the EQ Mode to Graphic EQ. For details, refer to "Setting EQ mode" on page 37. 1 After selecting Graphic EQ from the Sound Field Adjustment mode, press BAND to select the band to be adjusted. Band 1  Band 2  Band 3  Band 4  Band 5  Band 6  Band 7  Band 1 Band-1 Band-2 63 Hz 150 Hz Band-3 400 Hz Band-4 1 kHz Band-5 2.5 kHz Band-6 6.3 kHz Band-7 17.5 kHz 2 Turn the Rotary encoder to adjust the level. Adjustable output level: −6 to +6 dB 3 To adjust another band, repeat steps 1 and 2, and then adjust all bands. Adjusting the Time Correction Before performing the following procedures, refer to "About Time Correction" on page 39. 1 After selecting T.Correction from the Sound Field Adjustment mode, press BAND to select a speaker to be adjusted. 2.2ch (3WAY) System F-L*1  F-R*2  R-L*3  R-R*4  SW-L  SW-R  F-L *1 Mid-L (Initial setting) *2 Mid-R *3 High-L *4 High-R 4.2ch (FRONT/REAR/SUBW.) System F-L*1  F-R*2  R-L*3  R-R*4  SW-L  SW-R  F-L *1 Front-L (Initial setting) *2 Front -R *3 Rear-L *4 Rear-R 2 Turn the Rotary encoder to adjust the distance correction value (0.0 to 336.6cm). L = (distance to farthest speaker) - (distance to other speakers) 3 Repeat steps 1 and 2 to set another speaker. By setting these values to make its sound reach the listening position at the same time as the sound of other speakers. Adjusting the Crossover Settings Before performing the following procedures, refer to "About the Crossover" on page 41. 2.2ch (3WAY) System 1 After selecting X-Over from the Sound Field Adjustment mode, press BAND to select the band to be adjusted. NORMAL (L=R)  Setting items: LOW / MID-L / MID-H / HIGH INDIVIDUAL (L/R)  Setting items: LOW-L / LOW-R / MID-L-L / MID-L-R / MID-H-L / MID-H-R / HIGH-L / HIGH-R 2 Press  or  to select the desired cut-off frequency (Crossover Point). Adjustable frequency bands: LOW / MID-L 20 Hz~200 Hz 38-EN