Alpine CDA-117 Owner's Manual (english) - Page 41
About Time Correction - no sound
UPC - 793276711656
View all Alpine CDA-117 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 41 highlights
MID-H HIGH 20 Hz~20 kHz (1 kHz~20 kHz)*1/(20 Hz~20 kHz)*2 *1 When FACTORY'S is selected, refer to "Setting the Response Slope for the High Range Speaker (TW Setup)" on page 37. *2 When USER'S is selected, refer to "Setting the Response Slope for the High Range Speaker (TW Setup)" on page 37. 3 Press SOURCE to adjust the slope. Adjustable slope: FLAT*, 6 dB/oct., 12 dB/oct., 18 dB/oct., 24 dB/ oct. * FLAT can be set for the HIGH slope only when TW Setup is set to USER'S (refer to "Setting the Response Slope for the High Range Speaker (TW Setup)" on page 37). Depending on the response characteristics of the speaker, care should be taken when setting the response slope to FLAT, as speaker damage may result. With this unit, a message is displayed when the response slope for the high range speaker is set to FLAT. 4 Turn the Rotary encoder to adjust the output level. Adjustable output level: −12 to 0 dB. 5 Repeat steps 1 to 4 to make adjustment to the other bands. 4.2ch (FRONT/REAR/SUBW.) System 1 After selecting X-Over from the Sound Field Adjustment mode, press BAND to select the band to be adjusted. NORMAL (L=R) Setting items: LOW (SUB-W) / MID (REAR) / HIGH (FRONT ) INDIVIDUAL (L/R) Setting items: LOW (SUB-W)-L / LOW (SUB-W)-R / MID (REAR)-L / MID (REAR)-R / HIGH (FRONT)-L / HIGH (FRONT )-R 2 Press or to select the desired cut-off frequency (Crossover Point). Adjustable frequency bands: 20 Hz~200 Hz 3 Press SOURCE to adjust the slope. Adjustable slope: FLAT, 6 dB/oct., 12 dB/oct., 18 dB/oct., 24 dB/ oct. 4 Turn the Rotary encoder to adjust the output level. Adjustable output level: −12 to 0 dB. 5 Repeat steps 1 to 4 to make adjustment to the other bands. Notes • While adjusting the X-Over, you should consider the frequency response of the connected speakers. • About the 2.2ch (3WAY)/4.2ch (FRONT/REAR/SUBW.) system, you can switch to 2.2ch (3WAY)/4.2ch (FRONT/REAR/SUBW.) system mode with the 2.2ch (3WAY)/4.2ch (FRONT/REAR/SUBW.) switch on the PXA-H100. For details, refer to the Owner's Manual of PXA-H100. Storing the Sound Field Adjustment Settings The Sound Field Adjustment Settings containing Parametric EQ/ Graphic EQ, T.Correction and X-Over settings can be stored in the preset memory. 1 When the settings of Sound Field Adjustment have been completed, select any one of the preset buttons (1 through 6) in any item of the Sound Field Adjustment mode (e.g. X-Over), press and hold the desired preset buttons for at least 2 seconds. 2 Turn the Rotary encoder to select PROTECT YES/NO, and then press ENTER to store the adjusted contents. PROTECT YES (Initial setting) PROTECT NO Notes • If YES is selected, the adjusted contents are protected and stored into the preset buttons. When you want to store the parameter into a protected preset button, "Replace NO/YES" can be selected. • If NO is selected, the preset is stored. • While performing this operation, all adjusted contents of Parametric EQ/Graphic EQ, T.Correction and X-Over will be stored in the preset buttons. • The stored contents are not deleted even when resetting the unit or disconnecting the battery. • The stored contents can be recalled by performing operation (refer to "Recalling the Stored Sound Field Adjustment Settings" on page 39). Recalling the Stored Sound Field Adjustment Settings The stored Sound Field Adjustment Settings contain Parametric EQ/ Graphic EQ, T.Correction and X-Over settings that are stored in the preset memory. 1 After selecting any item of the Sound Field Adjustment mode (e.g. X-Over), press any one of the preset buttons (1 through 6) that has your desired characteristic in memory to recall the stored settings. 2 Press the preset buttons (1 through 6) again to return to the Sound Field Adjustment mode. Note • While performing this operation, all adjustment contents of Parametric EQ/Graphic EQ, T.Correction and X-Over stored in the preset buttons will be recalled. About Time Correction The distance between the listener and the speakers in a car vary widely due to the complex speaker placement. This difference in the distances from the speakers to the listener creates a shift in the sounds image and frequency characteristics. This is caused by the time delay between the sound reaching the listener's right versus the left ear. To correct this, this unit is able to delay the audio signal to the speakers closest to the listener. This effectively creates a perception of increased distance for those speakers. The listener can be placed at an equal distance between the left and right speakers for optimum staging. The adjustment will be made for each speaker in 3.4cm steps. Listening Pos tion example as follows: 39-EN