Alpine CDE-124SXM Owner's Manual (english) - Page 15

Sound Setting You can flexibly customize the unit to suit your own preference and usage. From the AUDIO SETUP menu, Audio Setting can be modified. Use steps 1 to 5 to select one of the setting modes to modify. See the applicable section below for details about the selected setting item. 1 Press and hold AUDIOSETUP for at least 2 seconds to activate the SETUP mode. 2 Turn the Rotary encoder to select AUDIO, and then press ENTER. BLUETOOTH*1  GENERAL  AUDIO  DISPLAY  SXM SETUP*2  iPod & USB *1 Displayed only when INT MUTE is set to OFF, and the mode is set to other than BT AUDIO. (CDE-123 only) *2 Displayed only when a SiriusXM Tuner is connected and the current source is Satellite Radio (SIRIUSXM). (CDE-124SXM/ CDE-123 only) 3 Turn the Rotary encoder to select the desired sound setting menu, and then press ENTER. FACTORY EQ*3/*4  3BAND EQ*3/*5  HPF*3  SUBWOOFER  SUBW LPF*6  SUBW PHASE*6  SUBW SYS*6 *3 Adjustment cannot be performed when DEFEAT is set to ON. *4 The FACTORY EQ's setting value and 3BAND EQ's setting value are linkage. *5 The FACTORY EQ's setting value and 3BAND EQ's setting value are linkage. In step 3, three sound adjustment items (Bass, Mid and Treble) can be selected in 3BAND EQ mode, turn the Rotary encoder to select the desired item, and then press ENTER to continue to step 4. *6 These functions are inoperable when Subwoofer is set to OFF. 4 Turn the Rotary encoder to change the setting, and then press ENTER. (e.g. Select SUBWOOFER ON or SUBWOOFER OFF) 5 Press and hold AUDIOSETUP for at least 2 seconds to return to normal mode. Notes • Pressing  returns to the previous Sound menu mode. • If no operation is performed for 60 seconds, Sound menu mode is canceled. Equalizer Presets (FACTORY EQ) 10 typical equalizer settings are preset at the factory for a variety of musical source material. USER  FLAT  POPS  ROCK  NEWS  JAZZ  ELEC DANCE  HIP HOP  EASY LIS  COUNTRY  CLASSICAL Adjusting the Parametric Equalizer Curve (3BAND EQ) You can modify the Equalizer settings to create a response curve more appealing to your personal taste. The setting of Bass, Mid and Treble can be adjusted in this mode. Setting the Bass Control 1 After selecting BASS from the 3BAND EQ adjustment mode, turn the Rotary encoder to select the desired Bass setting item, and then press ENTER. WIDTH (Q)  CENTER FRQ  LEVEL 2 Turn the Rotary encoder to select the desired setting value, and then press ENTER. 3 Press  to return to the previous step.  Setting the Bass Bandwidth (WIDTH (Q)) Turn the Rotary encoder to select the desired bass bandwidth. WIDE 0.50  MEDIUM 1.00  MEDIUM 1.50  NARROW 2.00 Changes the boosted bass bandwidth to wide or narrow. A wider setting will boost a wide range of frequencies above and below the center frequency. A narrower setting will boost only frequencies near the center frequency.  Setting the Bass Center Frequency (CENTER FRQ) Turn the Rotary encoder to select the desired bass center frequency. 60 (Hz)  80 (Hz) (Initial setting)  100 (Hz)  120 (Hz) Emphasizes the displayed bass frequency ranges.  Setting the Bass Level Turn the Rotary encoder to select the desired bass level (-7~+7)*. You can emphasize or weaken the bass level. * The adjustment can also be made by pressing AUDIO. Refer to "Adjusting Subwoofer Level/Bass Level/Mid Level/Treble Level/ Balance (Between Left and Right)/Fader (Between Front and Rear)/Loudness/Defeat" on page 14. Setting the Mid Control 1 After selecting MID from the 3BAND EQ adjustment mode, turn the Rotary encoder to select the desired Mediant setting item, and then press ENTER. WIDTH (Q)  CENTER FRQ  LEVEL 2 Turn the Rotary encoder to select the desired setting value, and then press ENTER. 3 Press  to return to the previous step.  Setting the Mid Bandwidth (WIDTH (Q)) Turn the Rotary encoder to select the desired Mid bandwidth. WIDE 0.75  MEDIUM 1.00  MEDIUM 1.25  NARROW 1.50  Setting the Mid Center Frequency (CENTER FRQ) Turn the Rotary encoder to select the desired Mid center frequency. 500 (Hz)  1.0k (Hz) (Initial setting)  1.5k (Hz)  2.5k (Hz) 15-EN