Alpine CDE-W235BT Owner's Manual (english) - Page 13
Sound Setting - bluetooth
View all Alpine CDE-W235BT manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 13 highlights
Sound Setting AUDIO/SETUP /ENTER Rotary encoder Adjusting Subwoofer Level/Bass Level/ Middle Level/Treble Level/Balance (Between Left and Right)/Fader (Between Front and Rear)/Loudness/Defeat 1 Press AUDIO/SETUP repeatedly to choose the desired mode. Each press changes the mode as follows: SUBWOOFER*1 BASS LEVEL*2 MID LEVEL*2 TRE LEVEL*2 BALANCE FADER LOUDNESS*2/*3 DEFEAT VOLUME SUBWOOFER *1 When the subwoofer mode is set to OFF, its level cannot be adjusted. *2 Adjustable only when DEFEAT is OFF. *3 For details about loudness, refer to "Turning Loudness On/Off " on page 13. Subwoofer Bass level Middle level Treble level Balance Fader Loudness Defeat Volume +0 ~ +15 -7 ~ +7 -7 ~ +7 -7 ~ +7 L15 ~ R15 R15 ~ F15 ON/OFF ON/OFF 0 ~ 35 Note • If no operation is performed for 5 seconds, the unit automatically returns to normal mode. 2 Turn the Rotary encoder until the desired sound is obtained in each mode. By setting DEFEAT ON, previously adjusted settings of BASS, MID, TRE LEVEL and LOUDNESS will return to the factory defaults. Audio Setup You can flexibly customize the unit to suit your own preference and usage. From the AUDIO SETUP menu, Audio Setting can be modified. Use steps 1 to 5 to select one of the setting modes to modify. See the applicable section below for details about the selected setting item. 1 Press and hold AUDIOSETUP for at least 2 seconds to activate the SETUP mode. 2 Turn the Rotary encoder to select AUDIO, and then press ENTER. AUDIO GENERAL DISPLAY IPOD BLUETOOTH 3 Turn the Rotary encoder to select the desired sound setting menu, and then press ENTER. FACTORY EQ*1/*2 LOUDNESS*1 3BAND EQ*1/*3 VOL LV ADJ HPF*1 SUBWOOFER SUBW LPF*1/*4 SUBW PHASE*4 SUBW SYS*4 POWER IC (e.g. Select SUBWOOFER) *1 Adjustment cannot be performed when DEFEAT is set to ON. *2 The FACTORY EQ's setting value and 3BAND EQ's setting value are linkage. *3 The FACTORY EQ's setting value and 3BAND EQ's setting value are linkage. In step 3, three sound adjustment items (Bass, Mid and Treble) can be selected in 3BAND EQ mode, turn the Rotary encoder to select the desired item, and then press ENTER to continue to step 4. *4 These functions are inoperable when Subwoofer is set to OFF. 4 Turn the Rotary encoder to change the setting, and then press ENTER. (e.g. Select SUBW ON or SUBW OFF) 5 Press and hold AUDIOSETUP for at least 2 seconds to return to normal mode. Notes • Pressing returns to the previous Sound menu mode. • Pressing and holding for at least 2 seconds will return to normal mode. • If no operation is performed for 60 seconds, Sound menu mode is canceled. Equalizer Presets (F-EQ) 10 typical equalizer settings are preset at the factory for a variety of musical source material. Setting item: FACTORY EQ Setting contents: USER / FLAT (Initial setting) / POPS / ROCK / NEWS / JAZZ / ELEC DANCE / HIP HOP / EASY LIS / COUNTRY / CLASSICAL Turning Loudness On/Off Loudness introduces a special low-and high-frequency emphasis at low listening levels. This compensates for the ear's decreased sensitivity to bass and treble sound. Setting item: LOUDNESS Setting contents: LOUD OFF (Initial setting) / LOUD ON 13-EN