Alpine PXE-H660 Owners Manual - Page 11

Before Setup

Get Alpine PXE-H660 PDF manuals and user guides
UPC - 793276310286
View all Alpine PXE-H660 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

BEFORE SETUP The following guidelines will ensure a smooth and accurate setup procedure. Have the MultEQ CD, microphone and MultEQ LED available and take a note of the conditions below as they are needed in the next section. 1. The PXE-H660 has the ability to drive a full-range or two-way front speaker output system configuration. In the case of a two-way system (bi-amping a set of components), make sure the tweeter amplifier channels go to the L1/R1 RCA outputs and the midrange amplifier channels go to the L2/R2 RCA outputs. At this time, set the crossover point for the high-pass speakers. Use the manufacturer recommended tweeter high-pass crossover frequency point (5 kHz by default). The mid-bass lowpass cut-off is determined by tweeter high-pass. If there is a subwoofer in the system, the low pass cut-off will be set automatically by MultEQ. In the case of a full-range system, the front speaker amplifier channels must connect to the FRONT L2/R2 outputs only. Full-Range Two-Way Only use L2/R2 RCA outputs to the front speaker amplifier channel Use L1/R1 RCA outputs to the tweeter amplifier channels, and use L2/R2 RCA outputs to the midrange amplifier channels Front Speaker Amp Tweeter Amp Front Midrange Amp Front Speakers Front Speakers 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
11
The following guidelines will ensure a smooth and accurate setup procedure. Have the
MultEQ
CD, microphone and
MultEQ LED available and take a note of the conditions
below as they are needed in the next section.
1. The PXE-H660 has the ability to drive a full-range or two-way front speaker output
system configuration. In the case of a two-way system (bi-amping a set of compo
-
nents), make sure the tweeter amplifier channels go to the L1/R1 RCA outputs and
the midrange amplifier channels go to the L2/R2 RCA outputs. At this time, set the
crossover point for the high-pass speakers. Use the manufacturer recommended
tweeter high-pass crossover frequency point (5 kHz by default). The mid-bass low-
pass cut-off is determined by tweeter high-pass. If there is a subwoofer in the system,
the low pass cut-off will be set automatically by MultEQ. In the case of a full-range
system, the front speaker amplifier channels must connect to the FRONT L2/R2
outputs only.
BEFORE SETUP
Full-Range
Two-Way
Only use L2/R2 RCA
outputs to the front
speaker amplifier
channel
Use L1/R1 RCA
outputs to the tweeter
amplifier chan
-
nels, and use L2/R2
RCA outputs to the
midrange amplifier
channels
Front Speaker Amp
Tweeter Amp
Front Midrange Amp
Front Speakers
Front Speakers