Alpine PXE-H660 Owners Manual - Page 49

l1lil1li

Get Alpine PXE-H660 PDF manuals and user guides
UPC - 793276310286
View all Alpine PXE-H660 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

#/7bILPINE~ PXE-H660 Quick Setup Guide Play track 2 on the PXE-H660's set-up CD. Press "Enter" on the PXE-H660's control panel. Reduce the sub amp (s) levels to l!4 gain (9 o'clock position). Press "Enter" on the PXEH660's control panel. oint the remote control at the remote eye and press "C". Note: There is an insulator tab under the remote battery that needs to be removed before use. l1li Place the microphone in position -- When position 1 is finished, the status 1, at the drivers ear level. Close all LED will start flashing once per sec- doors and windows, and keep the ond. Move the microphone to position area around the car quiet. The status 2, at the passengers ear level. Close LED should now be blinking once per second. all doors and windows again, and press "c" on Press "c" on the remote control. The status LED the remote control. The status LED shows solid shows solid green while position 1 is measured. green again l1lil1li When Position 2 is finished, the status LED will start flashing once per second. Move the microphone to position 3, 30" above the middle rear seat. Close all doors and windows again, and press "c" on the remote control.The status LED shows solid green again - - When Position 3 is finished, the status LED will start flashing once per second. Move the microphone to position 4, the middle of the front of the vehicle. Close all doors and windows again, and press "c" on the remote control. The status LED shows solid green again Turn up the sub gain to the desired level. Press Setup process is finished. Press "Enter" on the "Enter" on the PXE-H660's control panel. PXE-H660's control panel. 2009 ©Alpine Electronics of America, Inc. All Rights Reserved. - . r- ~,.""_. , I ..- I Press "VOL +" on the remote until the volume level is set at +35. ~ 1-.-..~INlIlIt_~ r-- '~~'-- '" Now the car's factory volume control can be used. .$ff/iLPINE. Mobile Media Solutions

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
...
1---
~
~INlIlIt_~
r--
'~~'--
'"
oint the remote control at the
remote eye and press "C". Note:
There is an insulator tab under the remote bat-
tery that needs to be removed before use.
Now the car's factory volume control can be
used.
--
When Position 3 is finished, the
status LED will start flashing once
per second. Move the microphone
to
position 4, the middle
of
the front
of
the vehicle. Close all doors and windows again,
and press
"c"
on the remote control. The status
LED shows solid green again
.
r-
-
~,.""_.
,
I
-
I
..
Press "VOL +" on the remote until
the volume level is set at +35.
Reduce the sub amp (s) levels to
l!4
gain (9
o'clock position). Press "Enter" on the PXE-
H660's control panel.
When Position 2 is finished, the
status LED will start flashing once
per second. Move the microphone to
position
3,
30" above the middle rear
seat. Close all doors and windows again, and
press
"c"
on the remote control.The status LED
shows solid green again
l1lil1li
Play track 2 on the PXE-H660's set-up CD.
Press "Enter" on the PXE-H660's control
panel.
Setup process
is
finished. Press "Enter" on the
PXE-H660's control panel.
When position 1
is
finished, the status
LED will start flashing once per sec-
ond. Move the microphone
to
position
2, at the passengers ear level. Close
all doors and windows again, and press
"c"
on
the remote control. The status LED shows solid
green again
--
l1li
Turn up the sub gain to the desired level. Press
"Enter" on the PXE-H660's control panel.
Place the microphone in position
1,
at the drivers ear level. Close all
doors and windows, and keep the
area around the car quiet. The status
LED should now be blinking once per second.
Press
"c"
on the remote control. The status LED
shows solid green while position 1 is measured.
#/7bILPINE~
PXE-H660 Quick Setup Guide
2009 ©Alpine Electronics
of
America, Inc.
All
Rights Reserved.
.$ff/iLPINE.
Mobile
Media
Solutions