Amana AGP200VDW Installation Instruction - Page 11
Check Operation of Oven/Broil Burner, Complete Installation
UPC - 883049214153
View all Amana AGP200VDW manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 11 highlights
Check Operation of Oven/Broil Burner 1. Make sure all controls are off and the oven is cool. 2. Open the oven door to remove oven racks and the oven bottom tray. 3. Remove the fasteners holding the flame spreader. Lift and pull out the flame spreader. A A A. Oven bottom tray B. Fasteners B C. Flame spreader If the flame needs adjusting: 1. Turn the oven off. Wait for the oven burner to cool down. 2. Open oven door and remove oven racks, oven bottom tray, flame spreader and set aside. A A A. Oven bottom tray B B. Fasteners C. Flame spreader C C 3. Locate the air shutter near the rear wall of oven and loosen the shutter screw. 4. Locate the pilot light on the left-hand side of the oven burner. 5. Push in oven control knob and hold, then ignite the oven pilot light with a match. A B A. Oven burner B. Oven Pilot 6. Hold the oven control knob in for 10 seconds to make sure the pilot will remain lit. 7. If the oven pilot light truns off after releasing the knob, repeate steps 5 and 6. 8. When the oven pilot remains on, replace the flame spreader, oven bottom tray, and racks. NOTE: The pilot light will stay light after turning off the oven. The oven burner should turn on the next time a temperature is selected on the oven control knob. If the oven burner does not turn on, repeat previous steps for lighting oven pilot light. 9. Open broiler door. 10. Push in and turn the oven control knob to 350˚ F. The oven pilot should now be larger with the flame burning against a small metal bulb. The oven burner should light in 20-40 seconds; this delay is normal. The oven valve requires a certain time before it will open and allow gas to flow. OFOFFF 242040 303000 353050 404000 OVOEVNETNETMEPMP BroBirloil 454050 5005050P2U05PS2UH0STHOTTOUTRUNRN 11. Check the oven burner for proper flame. The flame should be 1/2" (13 mm) long, with inner cone of bluish-green, and outer mantle of dark blue, and should be clean and soft in character. No yellow tips (not enough air), blowing or lifting (too much air) of flame should occur. A B A. Shutter screw B. Air shutter 4. Adjust the air shutter. 5. Turn the oven back on and check for proper flame. If the flame is still not properly adjusted, turn the oven off, wait for the oven burner to cool down and repeat step 4 until flame is properly adjusted. 6. When the flame has been properly adjusted, turn the oven off, wait for the burner to cool down. 7. Tighten the shutter screw. 8. Reinstall flame spreader and oven tray. Reinstall the oven racks and close oven door. Complete Installation 1. Check to be sure all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped. 2. Check to be sure you have all of your tools. 3. Dispose of/recycle all packaging materials. 4. Check to be sure the range is level. See "Level Range." 5. Use a mild solution of liquid household cleaner and warm water to remove waxy residue caused by protective shipping material. Dry thoroughly with a soft cloth. 6. For range use and cleaning, read the range Use and Care Guide. 7. Turn on surface burners and oven. If range does not operate, check the following: ■ See "Troubleshooting" in your Use and Care Guide. ■ When the range has been on for 5 minutes, feel for heat. If you do not feel heat, turn the range off and check to see that the gas supply line shutoff valve is open. ■ If the gas supply line shutoff valve is closed, open it, then repeat the 5 minute test as outlined above. ■ If the gas supply line shutoff valve is open, contact a qualified technician. 11