Asus Terminator K7 E732 MANUAL TERMINATOR K7 English V1.0 - Page 28

Re-connect Cables

Get Asus Terminator K7 PDF manuals and user guides View all Asus Terminator K7 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

2.9 Re-connect Cables You may have disconnected some cables when you were installing components. You must re-connect these cables before you replace the chassis cover. 2.9.1 Front Panel Cables The figures below show the front panel cables with corresponding instructions on where to connect them. You must re-connect these cables before replacing the chassis cover. Power Switch Power LED HDD LED Line Out / Mic USB Connector (USB2P) 1. Connect the power switch and power LED cables to their respective leads in the PANEL connector on the motherboard. 2. Connect the HDD LED cable to the 2-pin lead marked IDELED. 3. Connect the Line Out/Mic cable to the FLOUT/MIC2 connector on the motherboard, matching the red pin stripe with Pin 1. 4. Connect the USB2P cable to the USB1 connector on the motherboard, matching the red pin stripe with Pin 1. 28 Chapter 2: Basic Installation

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
28
Chapter 2:
Basic Installation
2.9
Re-connect Cables
You may have disconnected some cables when you were installing
components. You must re-connect these cables before you replace
the chassis cover.
2.9.1
Front Panel Cables
1. Connect the power switch and power LED cables to their
respective leads in the PANEL connector on the motherboard.
2.
Connect the HDD LED cable to the 2-pin lead marked IDELED.
3.
Connect the Line Out/Mic cable to the FLOUT/MIC2 connector
on the motherboard, matching the red pin stripe with Pin 1.
4. Connect the USB2P cable to the USB1 connector on the
motherboard, matching the red pin stripe with Pin 1.
Power Switch
Power LED
HDD LED
Line Out / Mic
USB Connector (USB2P)
The figures below show the front panel cables with corresponding
instructions on where to connect them. You must re-connect these
cables before replacing the chassis cover.