Asus Terminator K7 E732 MANUAL TERMINATOR K7 English V1.0 - Page 43

ASUS Terminator K7 Barebone System, USB Device Wake Up Front and Back Panel USB Ports., CPU/FSB

Get Asus Terminator K7 PDF manuals and user guides View all Asus Terminator K7 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

2. CPU/FSB Frequency Selection. The FS jumper is set to a factory default [2-3] that operates with AMD 100 MHz FSB capacity processors. If AMD 133 MHz capacity processors are used, then reset the jumper to [1-2]. The FS jumper settings should match the capacity of the processor. Otherwise, the motherboard may not boot up. FS1 & FS2 A7VC 12 23 CPU 133MHz CPU 100MHz ® A7VC CPU FSB Frequency Setting 3. USB Device Wake Up (Front and Back Panel USB Ports). Set these jumpers to +5V to allow wake up from S1 sleep state (CPU stopped; RAM refreshed; system running in low power mode) using the connected USB devices. Set to +5VSB to allow wake up from S3 state (no power to CPU; RAM in slow refresh; power supply in reduced power mode). JP1A 12 23 A7VC +5V +5VSB (Back Panel USB Port) JP1B 12 23 ® A7VC USB Ports Setting +5V +5VSB (Front Panel USB Port) ASUS Terminator K7 Barebone System 43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
ASUS Terminator K7 Barebone System
43
3.
USB Device Wake Up (Front and Back Panel USB Ports).
Set these jumpers to +5V to allow wake up from S1 sleep state
(CPU stopped; RAM refreshed; system running in low power
mode) using the connected USB devices. Set to +5VSB to allow
wake up from S3 state (no power to CPU; RAM in slow refresh;
power supply in reduced power mode).
A7VC
A7VC CPU FSB Frequency Setting
CPU 133MHz
12
23
FS1 & FS2
CPU 100MHz
2.
CPU/FSB Frequency Selection.
The FS jumper is set to a
factory default [2-3] that operates with AMD 100 MHz FSB
capacity processors. If AMD 133 MHz capacity processors are
used, then reset the jumper to [1-2]. The FS jumper settings
should match the capacity of the processor. Otherwise, the
motherboard may not boot up.
A7VC
A7VC USB Ports Setting
(Back Panel USB Port)
JP1A
+5V
12
23
+5VSB
(Front Panel USB Port)
JP1B
+5V
12
23
+5VSB