Asus Terminator K7 E732 MANUAL TERMINATOR K7 English V1.0 - Page 50

Connectors

Get Asus Terminator K7 PDF manuals and user guides View all Asus Terminator K7 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

3.9 Connectors 3.9.1 External Connectors WARNING! Some pins are used for connectors or power sources. These are clearly distinguished from jumpers in the Motherboard Layout. Placing jumper caps over these connector pins will cause damage to your motherboard. IMPORTANT Ribbon cables should always be connected with the red stripe to Pin 1 on the connectors. Pin 1 is usually on the side closest to the power connector on hard drives and CD-ROM drives, but may be on the opposite side on floppy disk drives. Check the connectors before installation because there may be exceptions. IDE ribbon cable must be less than 46 cm (18 in.), with the second drive connector no more than 15 cm (6 in.) from the first connector. 1. PS/2 Mouse Connector (Green 6-pin PS2KBMS) The system automatically directs IRQ12 to the PS/2 mouse if one is detected. If no mouse is detected, IRQ12 become available to expansion cards. See PS/2 Mouse Function Control in 4.7 Advanced Menu. PS/2 Mouse (6-pin female) 2. PS/2 Keyboard Connector (Purple 6-pin PS2KBMS) This connection is for a standard keyboard using an PS/2 plug (mini DIN). This connector does not allow standard AT size (large DIN) keyboard plugs. You may use a DIN to mini DIN adapter on standard AT keyboards. PS/2 Keyboard (6-pin female) 50 Chapter 3: Motherboard Information

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
50
Chapter 3:
Motherboard Information
2.
PS/2 Keyboard Connector
(Purple 6-pin PS2KBMS)
This connection is for a standard keyboard using an PS/2 plug
(mini DIN).
This connector does not allow standard AT size
(large DIN) keyboard plugs.
You may use a DIN to mini DIN
adapter on standard AT keyboards.
PS/2 Mouse (6-pin female)
PS/2 Keyboard (6-pin female)
3.9
Connectors
1.
PS/2 Mouse Connector
(Green 6-pin PS2KBMS)
The system automatically directs IRQ12 to the PS/2 mouse if
one is detected. If no mouse is detected, IRQ12 become available
to expansion cards. See
PS/2 Mouse Function Control
in
4.7
Advanced Menu
.
3.9.1
External Connectors
WARNING!
Some pins are used for connectors or power sources. These are
clearly distinguished from jumpers in
the Motherboard Layout. Placing
jumper caps over these connector pins will cause damage to your
motherboard.
IMPORTANT
Ribbon cables should always be connected with the red stripe to Pin
1 on the connectors. Pin 1 is usually on the side closest to the power
connector on hard drives and CD-ROM drives, but may be on the
opposite side on floppy disk drives. Check the connectors before
installation because there may be exceptions. IDE ribbon cable must
be less than 46 cm (18 in.), with the second drive connector no more
than 15 cm (6 in.) from the first connector.