Biostar M7VKQ M7VKQ user's manual - Page 53

AGP Driving Control, AGP Driving Value, OnChip USB, USB Keyboard Support, OnChip Sound, OnChip Modem

Get Biostar M7VKQ PDF manuals and user guides View all Biostar M7VKQ manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

Chapter 2 BIOS Setup AGP Driving Control By choosing "Auto" the system BIOS will the AGP output Buffer Drive strength P Ctrl by AGP Card. By choosing "Manual", it allows user to set AGP output Buffer Drive strength P Ctrl by manual. The Choices: Auto (default), Manual. AGP Driving Value While AGP driving control item set to "Manual", it allows user to set AGP driving. The Choices: DA (default). OnChip USB This should be enabled if your system has a USB installed on the system board and you wish to use it. Even when so equipped, if you add a higher performance controller, you will need to disable this feature. The Choices: Enabled (default), Disabled. USB Keyboard Support Select Enabled if your system contains a Universal Serial Bus (USB) controller and also you have a USB keyboard. The Choices: Disabled (default), Enabled. OnChip Sound The default setting of this item utilizes an onboard sound chip for audio output. There is no need to buy and insert a sound card. If sound card is installed, disable this item. The Choices: Auto (default), Disabled. OnChip Modem This item allows you to control the onboard MC97 Modem controller. The Choices: Auto (default), Disabled. CPU to PCI Write Buffer When enabled, up to four Dwords of data, it can be written to the PCI bus without interrupting the CPU. When disabled, a write buffer is not used, and the CPU read cycle will not be completed until the PCI bus signals that it is ready to receive the data. The Choices: Enabled (default), Disabled. 2-16

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
Chapter 2
BIOS Setup
2-16
AGP Driving Control
By choosing “Auto” the system BIOS will the AGP output Buffer Drive strength P
Ctrl by AGP Card. By choosing “Manual”, it allows user to set AGP output Buffer
Drive strength P Ctrl by manual.
The Choices: Auto
(default), Manual.
AGP Driving Value
While AGP driving control item set to “Manual”, it allows user to set AGP driving.
The Choices: DA
(default).
OnChip USB
This should be enabled if your system has a USB installed on the system board and
you wish to use it. Even when so equipped, if you add a higher performance
controller, you will need to disable this feature.
The Choices: Enabled
(default), Disabled.
USB Keyboard Support
Select Enabled if your system contains a Universal Serial Bus (USB) controller and
also you have a USB keyboard.
The Choices: Disabled
(default)
,
Enabled.
OnChip Sound
The default setting of this item utilizes an onboard sound chip for audio output.
There is no need to buy and insert a sound card. If sound card is installed, disable
this item.
The Choices: Auto
(default), Disabled.
OnChip Modem
This item allows you to control the onboard MC97 Modem controller.
The Choices: Auto
(default)
,
Disabled.
CPU to PCI Write Buffer
When enabled, up to four Dwords of data, it can be written to the PCI bus without
interrupting the CPU. When disabled, a write buffer is not used, and the CPU read
cycle will not be completed until the PCI bus signals that it is ready to receive the
data.
The Choices: Enabled
(default), Disabled.