Biostar M7VKQ M7VKQ user's manual - Page 56

Onboard FDD Controller, Onboard Serial Port, IrDA Port, UART 2 Mode, IR Function Duplex, TX

Get Biostar M7VKQ PDF manuals and user guides View all Biostar M7VKQ manuals
Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

Chapter 2 BIOS Setup Onboard FDD Controller Select Enabled, if your system has a floppy disk controller (FDC) installed on the system board, and if you wish to use it. If install and FDC or the system has no floppy drive, select Disabled in this field. The Choices: Enabled (default), Disabled. Onboard Serial Port Select an address and corresponding interrupt for the first and second serial ports. The Choices: 3F8/IRQ4 (default), Disabled, Auto, 2F8/IRQ3, 3E8/ IRQ4, 2E8 / IRQ3. IrDA Port Select an address and corresponding interrupt for the first and second serial ports. The Choices: Disabled (default), Auto, 3F8/IRQ4, 2F8/IRQ3, 3E8/ IRQ4, 2E8 / IRQ3. UART 2 Mode This item allows you to determine which Infrared (IR) function of the onboard I/O chip you wish to use. The Choices: HPSIR (default), ASKIR. IR Function Duplex This item allows you to determine which Infrared (IR) function of onboard I/O chip. The Choices: Half (default), Full. TX, RX inverting enable This item allows you to determine the active of Rx, Tx. The Choices: No, No No, Yes (default) Yes, No Yes, Yes Onboard Parallel Port This item allows you to determine access onboard parallel port controller with which I/O address. The Choices: Disabled, 3BC/IRQ0, 378/IRQ7 (default), 278/IRQ5. 2-19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
Chapter 2
BIOS Setup
2-19
Onboard FDD Controller
Select Enabled, if your system has a floppy disk controller (FDC) installed on the
system board, and if you wish to use it. If install and FDC or the system has no
floppy drive, select Disabled in this field.
The Choices: Enabled
(default), Disabled.
Onboard Serial Port
Select an address and corresponding interrupt for the first and second serial ports.
The Choices: 3F8/IRQ4
(default), Disabled, Auto, 2F8/IRQ3, 3E8/
IRQ4, 2E8 / IRQ3.
IrDA Port
Select an address and corresponding interrupt for the first and second serial ports.
The Choices: Disabled
(default), Auto, 3F8/IRQ4, 2F8/IRQ3, 3E8/
IRQ4, 2E8 / IRQ3.
UART 2 Mode
This item allows you to determine which Infrared (IR) function of the onboard I/O
chip you wish to use.
The Choices: HPSIR
(default), ASKIR.
IR Function Duplex
This item allows you to determine which Infrared (IR) function of onboard I/O
chip.
The Choices:
Half
(default), Full.
TX, RX inverting enable
This item allows you to determine the active of Rx, Tx.
The Choices:
No, No
No, Yes
(default)
Yes, No
Yes, Yes
Onboard Parallel Port
This item allows you to determine access onboard parallel port controller with
which I/O address.
The Choices:
Disabled, 3BC/IRQ0,
378/IRQ7
(default), 278/IRQ5.